Iei-integration UPC-V315-NM70 Manual de usuario

UPC-V315-NM70 Panel PC Page i IEI Technology Corp. User Manual UPC-V315-NM70 Panel PC MODEL: UPC-V315-NM70 Panel PC with Touch Screen and Intel® Cel

UPC-V315-NM70 Panel PC Page x Figure B-13: Symantec Ghost Path ...

UPC-V315-NM70 Panel PC Page 89 B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system ba

UPC-V315-NM70 Panel PC Page 90 After completing the five initial setup procedures as described above, users can access the recovery tool by pressing

UPC-V315-NM70 Panel PC Page 91 partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Imag

UPC-V315-NM70 Panel PC Page 92 o Ubuntu 8.10 (Intrepid) o Ubuntu 7.10 (Gutsy) o Ubuntu 6.10 (Edgy) o Debian 5.0 (Lenny) o Debian 4.0 (Etch) o

UPC-V315-NM70 Panel PC Page 93 B.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a hard dri

UPC-V315-NM70 Panel PC Page 94 Figure B-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure B-3: Reco

UPC-V315-NM70 Panel PC Page 95 Figure B-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) t

UPC-V315-NM70 Panel PC Page 96 Figure B-5: Partition Creation Commands

UPC-V315-NM70 Panel PC Page 97 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key t

UPC-V315-NM70 Panel PC Page 98 B.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. St

UPC-V315-NM70 Panel PC Page xi Lis t of Tables Table 1-1: LED Indicators ...

UPC-V315-NM70 Panel PC Page 99 Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this p

UPC-V315-NM70 Panel PC Page 100 B.2.5 Create Factory Default Im a g e NOTE: Before creating the factory default image, please configure the syste

UPC-V315-NM70 Panel PC Page 101 Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure B-13).

UPC-V315-NM70 Panel PC Page 102 Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in F

UPC-V315-NM70 Panel PC Page 103 Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure B-17 prompts, click High

UPC-V315-NM70 Panel PC Page 104 Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creati

UPC-V315-NM70 Panel PC Page 105 Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. St ep 0: Fi

UPC-V315-NM70 Panel PC Page 106 Figure B-22: Auto Recovery Utility Step 3: Reboot the system from the recovery CD. When prompted, press any key t

UPC-V315-NM70 Panel PC Page 107 Step 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition. In

UPC-V315-NM70 Panel PC Page 108 Step 7: The Symantec Ghost starts to create the factory default image (Figure B-27). Figure B-27: Image Creation C

UPC-V315-NM70 Panel PC Page 1 1 Introduction Chapter 1

UPC-V315-NM70 Panel PC Page 109 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit iEi Feature  Auto Re

UPC-V315-NM70 Panel PC Page 110 Step 2: Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) MBR type and Ext3 partition ty

UPC-V315-NM70 Panel PC Page 111 DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N: /fs:

UPC-V315-NM70 Panel PC Page 112 Figure B-31: Access menu.lst in Linux (Text Mode) Step 6: Modify the menu.lst as shown below. Step 7: The reco

UPC-V315-NM70 Panel PC Page 113 B.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can access the r

UPC-V315-NM70 Panel PC Page 114 WARNING: All data in the system will be deleted during the system recovery. Please backup the system files before

UPC-V315-NM70 Panel PC Page 115 Figure B-35: Recovery Complete Window B.5.2 Backup System To backup the system, please follow the steps below. Step

UPC-V315-NM70 Panel PC Page 116 Figure B-37: System Backup Complete Window B.5.3 Restore Your Last Backup To restore the last system backup, please

UPC-V315-NM70 Panel PC Page 117 Figure B-39: Restore System Backup Complete Window B.5.4 Manual To restore the last system backup, please follow th

UPC-V315-NM70 Panel PC Page 118 B.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically r

UPC-V315-NM70 Panel PC Page 2 1.1 Overview Figure 1-1: UPC-V315-NM70 Panel PC The fanless UPC-V315-NM70 is Intel® Celeron® processor 847 powered

UPC-V315-NM70 Panel PC Page 119 B.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #a

UPC-V315-NM70 Panel PC Page 120 filename “pxelinux.0”; B.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tf

UPC-V315-NM70 Panel PC Page 121 Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.c

UPC-V315-NM70 Panel PC Page 122 B.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: #service xinetd restart CentOS #serv

UPC-V315-NM70 Panel PC Page 123 Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = ye

UPC-V315-NM70 Panel PC Page 124 Step 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1  remain

UPC-V315-NM70 Panel PC Page 125 NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinux pro

UPC-V315-NM70 Panel PC Page 126 B.7 Other Information B.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode o

UPC-V315-NM70 Panel PC Page 127 Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Step 6: In the

UPC-V315-NM70 Panel PC Page 128 Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu. Continue to follow the

UPC-V315-NM70 Panel PC Page 3 1.2 Model Variations The model numbers and model variations are listed below. Model CPU UPC-V315-NM70-C/R/2G-R10 Inte

UPC-V315-NM70 Panel PC Page 129 C Safety Precautions Appendix C

UPC-V315-NM70 Panel PC Page 130 WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precaution

UPC-V315-NM70 Panel PC Page 131 C.1.2 An ti-static Precautions WARNING: Failure to take ESD precautions during the installation of the EP series m

UPC-V315-NM70 Panel PC Page 132  Outside the European Union - If you wish to dispose of used electrical and electronic products outside the Europe

UPC-V315-NM70 Panel PC Page 133 C.2.2 Cleaning Tools Some components in the EP series may only be cleaned using a product specifically designed for

UPC-V315-NM70 Panel PC Page 134 D Hazardous Materials Dis clos ure Appendix E

UPC-V315-NM70 Panel PC Page 135 D.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercur

UPC-V315-NM70 Panel PC Page 136 Part Name Toxic or Hazardous Substances and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (CR(V

UPC-V315-NM70 Panel PC Page 137 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较

UPC-V315-NM70 Panel PC Page 4 supports auto-focus (AF), auto-exposure (AE) and auto white balance (AWB). The front panel also has following buttons,

UPC-V315-NM70 Panel PC Page 5 1.4.1.1 LED Indicators The LED indicators on the front panel of the UPC-V315-NM70 are shown below. Figure 1-3: LED

UPC-V315-NM70 Panel PC Page 6 Controlled by the BIOS (see Section 4.4.1). Auto Dimming The auto dimming function is enabled or disabled. Controlled

UPC-V315-NM70 Panel PC Page 7  1 x HDMI connector  2 x RJ-45 GbE connectors  3 x RS-232 serial port connectors by RJ-45  1 x RS-422/485 se

UPC-V315-NM70 Panel PC Page 8 1.4.3 Side Panels The left side panel of the panel PC provides access to the HDD dive bay. (Figure 1-5) Figure 1-5

UPC-V315-NM70 Panel PC Page ii Revis ion Date Version Changes 3 May, 2013 1.00 Initial release

UPC-V315-NM70 Panel PC Page 9 1.4.5 Frame (Function Keys) An aluminum frame surrounds the TFT LCD screen. The aluminum frame of the UPC-V315-NM70

UPC-V315-NM70 Panel PC Page 10 1.5 Dimensions The dimensions of the UPC-V315-NM70 are shown in Figure 1-9 and listed below. Figure 1-9: UPC-V315-N

UPC-V315-NM70 Panel PC Page 11 1.6 Specifications The technical specifications for the UPC-V315-NM70 system are listed in Table 1-3. Specification U

UPC-V315-NM70 Panel PC Page 12 Audio AMP 3W + 3W (Internal Speaker) Camera 2M Mega Pixels Connectivity Wireless IEEE 802.11a/b/g/n 3T3R module (WIFI

UPC-V315-NM70 Panel PC Page 13 Power Adapter 90 W; 63040-010090-020-RS Requirement Power1:9V~36V(+/-0.3V) Power2:10.5V~36V(+/-0.3V) I/O Ports and Sw

UPC-V315-NM70 Panel PC Page 14 2 Unpacking Chapter 2

UPC-V315-NM70 Panel PC Page 15 2.1 Unpacking To unpack the panel PC, follow the steps below: WARNING! The front side LCD screen has a protective p

UPC-V315-NM70 Panel PC Page 16 2.2 Packing Lis t The UPC-V315-NM70 panel PC is shipped with the following components: Quantity Ite m Im a g e 1

UPC-V315-NM70 Panel PC Page 17 8 VESA mount screw (M4) (P/N: 44005-040082-RS) 2 Mounting bracket (side panels) (P/N: 41003-0382C2-00-RS) 1 Scr

UPC-V315-NM70 Panel PC Page 18 3 In s ta llation Chapter 3

UPC-V315-NM70 Panel PC Page iii Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to im

UPC-V315-NM70 Panel PC Page 19 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the maintenance of the EP series may re

UPC-V315-NM70 Panel PC Page 20 configure the jumpers or plug in added peripheral devices, ground themselves first and wear and anti-static wristband

UPC-V315-NM70 Panel PC Page 21 NOTE: Please use the screw driver that comes with the UPC-V315-NM70 to remove the screws on the chassis. Figur

UPC-V315-NM70 Panel PC Page 22 Figure 3-3: Securing the SSD Step 5: Install the SSD. Correctly align the SSD bracket with the system and insert th

UPC-V315-NM70 Panel PC Page 23 Step 1: Remove the internal USB port cover by removing the seven retention screws. Figure 3-5: Internal USB Port Co

UPC-V315-NM70 Panel PC Page 24 3.6 Mounting the System WARNING: When mounting the panel PC onto an arm or onto the wall, it is better to have more

UPC-V315-NM70 Panel PC Page 25 Figure 3-8: Mounting Brackets (Side Panels) NOTE: When mounting the UPC-V315-NM70 on a vehicle, it is recommended

UPC-V315-NM70 Panel PC Page 26 To install the UPC-V315-NM70 on the arm, follow the directions below. NOTE: Make sure the arm supports standard VES

UPC-V315-NM70 Panel PC Page 27 Step 1: Locate the screw holes on the rear of the UPC-V315-NM70. This is where the stand bracket will be attached. T

UPC-V315-NM70 Panel PC Page 28 Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the four screw holes on the r

UPC-V315-NM70 Panel PC Page iv Table of Contents 1 INTRODUCTION ...

UPC-V315-NM70 Panel PC Page 29 Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket. (Figure 3-13). Figure

UPC-V315-NM70 Panel PC Page 30 Figure 3-14: I/O Cover Retention Screws Step 2: Connect the cable from the external peripheral device to the corres

UPC-V315-NM70 Panel PC Page 31 Figure 3-17: Rubber Gasket and Cable Step 5: Repeat steps to other connected cables. Step 6: Install the I/O cover

UPC-V315-NM70 Panel PC Page 32 Figure 3-20: AT/ATX Power Mode Switch 3.7.4 Audio Connectors The audio jacks connect to external audio devices. 

UPC-V315-NM70 Panel PC Page 33 Figure 3-22: HDMI Connection Step 3: Insert the HDMI connector. Gently insert the HDMI connector. The connector sho

UPC-V315-NM70 Panel PC Page 34 3.7.7 LAN Connector To connect the UPC-V315-NM70 to a network through the RJ-45 LAN connector, follow the steps below

UPC-V315-NM70 Panel PC Page 35 The pinouts of the RJ-45 LAN connector is shown below. Pin Description Pin Description 1 MDI0+ 2 MDI0- 3 MDI1+

UPC-V315-NM70 Panel PC Page 36 Figure 3-26: Power Input Connector 3.7.10 RJ-45 RS-232 Serial Port RS-232 serial port devices can be attached to t

UPC-V315-NM70 Panel PC Page 37 Pin Description Pin Description 3 TX 8 CTS 4 DTR 9 RI 5 GND Table 3-5: DB-9 Connector Pinouts To instal

UPC-V315-NM70 Panel PC Page 38 Figure 3-30: RJ-45 RS-422/485 Serial Port Pinout Location Pin Description Pin Description 1 N/A 5 N/A 2 TXD4

UPC-V315-NM70 Panel PC Page v 3.7.3 AT/ATX Power Mode Selection ... 313.7.4 A

UPC-V315-NM70 Panel PC Page 39 Step 5: Locate the RJ-45 RS-422/485 connector. The location of the RJ-45 RS-422/485 connector is shown in Figure 1-4

UPC-V315-NM70 Panel PC Page 40 Figure 3-33: USB Device Connection Step 3: Insert the device connector. Once aligned, gently insert the USB device

UPC-V315-NM70 Panel PC Page 41 Figure 3-34: VGA Connector Pin Description Pin Description 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND

UPC-V315-NM70 Panel PC Page 42 Figure 3-35: VGA Connector CAUTION: It is suggested that not to open the rear cover and replace any component

UPC-V315-NM70 Panel PC Page 43 3.8 Redundant Power The UPC-V315-NM70 is a system that supports redundant power. The redundant power input increases

UPC-V315-NM70 Panel PC Page 44 3.8.1 ACC ON NOTE: In ACC On mode, the Power 1 connector must connect to the ACC on signal to be able to control sy

UPC-V315-NM70 Panel PC Page 45 3.8.1.2 Switch to Backup Power During operation, system power will switch from Power 1 to Power 2 automatically when

UPC-V315-NM70 Panel PC Page 46 Figure 3-40: ACC On: Shutdown NOTE: To turn on the system in ATX power mode, press the button for three second

UPC-V315-NM70 Panel PC Page 47 Figure 3-41: ACC Off: AT Mode Figure 3-42: ACC Off: ATX Mode 3.8.2.2 Switch to Backup Power During operation, syst

UPC-V315-NM70 Panel PC Page 48 3.8.2.3 Shutdown The system will shutdown in the following situations:  Power 2 < 10.5V and Power 1 < 9V

UPC-V315-NM70 Panel PC Page vi 4.3.5 USB Configuration ...

UPC-V315-NM70 Panel PC Page 49 3.9 Remote Control The UPC-V315-NM70 comes with a remote control for easy configuration. Figure 3-45 shows the remote

UPC-V315-NM70 Panel PC Page 50 4 BIOS Chapter 4

UPC-V315-NM70 Panel PC Page 51 4.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system s

UPC-V315-NM70 Panel PC Page 52 Key Function Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup M

UPC-V315-NM70 Panel PC Page 53 4.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an ov

UPC-V315-NM70 Panel PC Page 54  System Overview The system overview lists a brief summary of the BIOS. The fields in system overview cannot be cha

UPC-V315-NM70 Panel PC Page 55 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Ex

UPC-V315-NM70 Panel PC Page 56  ACPI Sleep State [S1 (CPU Stop Clock)] Use the ACPI Sleep State option to specify the sleep state the system enter

UPC-V315-NM70 Panel PC Page 57  Wake system with Fixed Time [Dis abled] Use the Wake system with Fixed Time option to enable or disable the system

UPC-V315-NM70 Panel PC Page 58 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced CPU Configuration Intel(R) Celer

UPC-V315-NM70 Panel PC Page vii B.6 RESTORE SYSTEMS FROM A LINUX SERVER THROUGH LAN ... 118B.6.1 Configure DHCP Se

UPC-V315-NM70 Panel PC Page 59 4.3.4 S ATA Configuration Use the SATA Configuration menu (BIOS Menu 6) to change and/or set the configuration of t

UPC-V315-NM70 Panel PC Page 60 4.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and config

UPC-V315-NM70 Panel PC Page 61  Disabled Legacy USB support disabled  Auto Legacy USB support disabled if no USB devices are connected 4.3.6 F

UPC-V315-NM70 Panel PC Page 62 4.3.6.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 9) to configure the serial po

UPC-V315-NM70 Panel PC Page 63  IO=3F8h; IRQ=3, 4 Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4  IO=2F8h; IRQ=3, 4 S

UPC-V315-NM70 Panel PC Page 64  Enabled DEFAULT Enable the serial port  Change Settings [Au to] Use the Change Settings option to change the ser

UPC-V315-NM70 Panel PC Page 65  IO=2E0h; IRQ=5, 7 Serial Port I/O port address is 2E0h and the interrupt address is IRQ5, 7  IO=2E8h; IRQ=5, 7 S

UPC-V315-NM70 Panel PC Page 66 o V_5S o V_12S o V_1.5V o VSB5V o VCC3V o VSB3V 4.3.8 Serial Port Console Redirection The Serial Port Cons

UPC-V315-NM70 Panel PC Page 67  Te rm in a l Typ e [ANSI] Use the Terminal Type option to specify the remote terminal type.  VT100 The target

UPC-V315-NM70 Panel PC Page 68  Even The parity bit is 0 if the number of ones in the data bits is even.  Odd The parity bit is 0 if the numbe

UPC-V315-NM70 Panel PC Page viii Lis t of Figures Figure 1-1: UPC-V315-NM70 Panel PC ...

UPC-V315-NM70 Panel PC Page 69 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Functi

UPC-V315-NM70 Panel PC Page 70 4.4 Chips et Use the Chipset menu (BIOS Menu 13) to access the PCH IO and System Agent (SA) configuration menus. WA

UPC-V315-NM70 Panel PC Page 71 4.4.1 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 14) to configure the PCH parameters. Aptio Se

UPC-V315-NM70 Panel PC Page 72  Disabled DEFAULT Disables 3G connection  GPS Support [Dis abled] Use the GPS Support option to enable or disable

UPC-V315-NM70 Panel PC Page 73 4.4.1.1 PCH Azalia Configuration Use the PCH Azalia Configuration menu (BIOS Menu 15) to configure the PCH Azalia set

UPC-V315-NM70 Panel PC Page 74 4.4.2 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 16) to configure the

UPC-V315-NM70 Panel PC Page 75 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Graphics Configuration Primary Disp

UPC-V315-NM70 Panel PC Page 76  DVMT To ta l Gfx Me m [MAX] Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used by

UPC-V315-NM70 Panel PC Page 77  LCD Panel Type [VBIOS ] Use the LCD Panel Type option to select the type of flat panel connected to the system. Co

UPC-V315-NM70 Panel PC Page 78 4.4.2.2 NB PCIe Configuration Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset NB PCI

UPC-V315-NM70 Panel PC Page ix Figure 3-23: LAN Connection ...

UPC-V315-NM70 Panel PC Page 79 4.4.2.3 Me m o ry Configuration Use the Memory Configuration submenu (BIOS Menu 20) to view memory information. Aptio

UPC-V315-NM70 Panel PC Page 80  Bootup NumLock State [On] Use the Bootup NumLock State BIOS option to specify if the number lock setting must be m

UPC-V315-NM70 Panel PC Page 81  Force BIOS Sets display mode to force BIOS.  Keep Current DEFAULT Sets display mode to current.  UEFI Boot [Dis

UPC-V315-NM70 Panel PC Page 82 4.6 Security Use the Security menu (BIOS Menu 22) to set system and user passwords. Aptio Setup Utility – Copyright (

UPC-V315-NM70 Panel PC Page 83 4.7 Save & Exit Use the Safe & Exit menu (BIOS Menu 23) to load default BIOS values, optimal failsafe values

UPC-V315-NM70 Panel PC Page 84  Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults.  Re

UPC-V315-NM70 Panel PC Page 85 A BIOS Me n u Options Appendix A

UPC-V315-NM70 Panel PC Page 86  System Overview ...

UPC-V315-NM70 Panel PC Page 87  Primary Display [Auto] .......

UPC-V315-NM70 Panel PC Page 88 Appendix B B One Key Recovery