Iei-integration WAFER-945GSELVDS2 Manual de usuario

WAFER-945GSELVDS2 Page iIEI Technology Corp. User Manual MODEL: WAFER-945GSELVDS2 3.5" SBC with 1.6 GHz Intel® ATOM™ N270VGA, Dual LVDS, Gigab

WAFER-945GSELVDS2Page x List of Tables Table 1-1: Technical Specifications...

WAFER-945GSELVDS2Page 88 5.3.5.2 APM Configuration The APM Configuration menu (BIOS Menu 10) allows the advanced power management options to be con

WAFER-945GSELVDS2 Page 89Î Suspend When the power button is pressed the system goes into suspend mode  Resume on Keyboard/Mouse [Disabled] Use th

WAFER-945GSELVDS2Page 90  Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system should be roused from a

WAFER-945GSELVDS2 Page 91 Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the s

WAFER-945GSELVDS2Page 92  57600 8,n,1  38400 8,n,1  19200 8,n,1  09600 8,n,1 NOTE: Identical baud rate setting musts be set on the host (a mana

WAFER-945GSELVDS2 Page 935.3.7 USB Configuration Use the USB Configuration menu to read USB configuration information and configure the USB settings

WAFER-945GSELVDS2Page 94  Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Norma

WAFER-945GSELVDS2 Page 955.3.7.1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu (BIOS Menu 13) to configur

WAFER-945GSELVDS2Page 96  Emulation Type [Auto] Use the Emulation Type BIOS option to specify the type of emulation BIOS has to provide for the US

WAFER-945GSELVDS2 Page 975.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 14) to configure advanced PCI and PnP settings. BIOS SETUP UTILITY Main Advanc

WAFER-945GSELVDS2 Page xiTable 4-1: Jumpers...

WAFER-945GSELVDS2Page 98  Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option to specify the amount of memory that should be

WAFER-945GSELVDS2 Page 995.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 16) to configure advanced system boot

WAFER-945GSELVDS2Page 100  AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messag

WAFER-945GSELVDS2 Page 1015.5.2 Boot Device Priority Use the Boot Device Priority menu to specify the boot sequence from the available devices. The

WAFER-945GSELVDS2Page 102 5.5.3 Hard Disk Drives Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. Only installed ha

WAFER-945GSELVDS2 Page 1035.5.5 CD/DVD Drives Use the CD/DVD Drives menu to specify the boot sequence of the available CD/DVD drives. Only connected

WAFER-945GSELVDS2Page 104  Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for t

WAFER-945GSELVDS2 Page 1055.7.1 Northbridge Configuration Use the Northbridge Chipset Configuration menu (BIOS Menu 23) to configure the Northbridge

WAFER-945GSELVDS2Page 106 Î Disable Î Enable, 1 MB 1 MB of memory used by internal graphics device Î Enable, 8 MB DEFAULT 8 MB of memory used b

WAFER-945GSELVDS2 Page 107 Boot Display Device Use the Boot Display Device option to select the display device used by the system when it boots. C

WAFER-945GSELVDS2Page xii BIOS Menus BIOS Menu 1: Main ...

WAFER-945GSELVDS2Page 108  LVDS2 Current Jumper Setting Shows the current hardware jumper setting for LVDS2. 5.7.2 Southbridge Configuration The S

WAFER-945GSELVDS2 Page 109Î Disabled DEFAULT EMI not reduced Î Enabled EMI reduced 5.8 Exit Use the Exit menu to load default BIOS values, optimal

WAFER-945GSELVDS2Page 110  Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameter

WAFER-945GSELVDS2 Page 111Appendix A A BIOS Options

WAFER-945GSELVDS2Page 112 Below is a list of BIOS configuration options in the BIOS chapter. 　 System Overview ...

WAFER-945GSELVDS2 Page 113　 Resume On RTC Alarm [Disabled]...90 　

WAFER-945GSELVDS2Page 114 　 Save Changes and Exit ...

WAFER-945GSELVDS2 Page 115Appendix B B Terminology

WAFER-945GSELVDS2Page 116 AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Powe

WAFER-945GSELVDS2 Page 117DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly wit

WAFER-945GSELVDS2 Page 1Chapter 1 1 Introduction

WAFER-945GSELVDS2Page 118 LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid

WAFER-945GSELVDS2 Page 119Appendix C C Digital I/O Interface

WAFER-945GSELVDS2Page 120 C.1 Introduction The DIO connector on the WAFER-945GSELVDS2 is interfaced to GPIO ports on the Super I/O chipset. The DIO

WAFER-945GSELVDS2 Page 121C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O

WAFER-945GSELVDS2Page 122 Appendix D D Watchdog Timer

WAFER-945GSELVDS2 Page 123 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specif

WAFER-945GSELVDS2Page 124 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM:

WAFER-945GSELVDS2 Page 125Appendix E E Hazardous Materials Disclosure

WAFER-945GSELVDS2Page 126 E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The

WAFER-945GSELVDS2 Page 127Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium(Cd) Hexavalent Chromium(CR(VI)) Polybr

WAFER-945GSELVDS2Page 2 1.1 Introduction Figure 1-1: WAFER-945GSELVDS2 The WAFER-945GSELVDS2 is a 3.5" motherboard with a 1.6 GHz Intel® ATOM™

WAFER-945GSELVDS2Page 128 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好

WAFER-945GSELVDS2 Page 3 Figure 1-2: WAFER-945GSELVDS2 Overview [Front View] 1.3 Technical Specifications WAFER-945GSELVDS2 technical specifications

WAFER-945GSELVDS2Page 4 Specification WAFER-945GSELVDS2 Memory One 200-pin SO-DIMM socket supports one 400 MHz or 533 MHz 2.0 GB (max.) DDR2 SDRAM

WAFER-945GSELVDS2 Page 51.4 Dimensions The dimensions of the board are shown below: Figure 1-3: Main Dimensions (mm)

WAFER-945GSELVDS2Page 6 Figure 1-4: Bottom Dimensions (mm) Figure 1-5: External Interface Panel Dimensions (mm)

WAFER-945GSELVDS2 Page 71.5 Data Flow Figure 1-6 shows the data flow between the two on-board chipsets and other components installed on the motherb

WAFER-945GSELVDS2Page ii Revision Date Version Changes 12 August, 2011 1.01 Modified SATA connector description 24 September, 2009 1.00 Initial r

WAFER-945GSELVDS2Page 8 Chapter 2 2 Unpacking

WAFER-945GSELVDS2 Page 92.1 Anti-static Precautions WARNING! Failure to take ESD precautions during the installation of the WAFER-945GSELVDS2 may r

WAFER-945GSELVDS2Page 10 2.3 Unpacking Checklist NOTE: If any of the components listed in the checklist below are missing, do not proceed with the

WAFER-945GSELVDS2 Page 11Quantity Item and Part Number Image 1 Utility CD 1 Quick Installation Guide Table 2-1: Packing List 2.3.2 Optional Ite

WAFER-945GSELVDS2Page 12 Chapter 3 3 Connectors

WAFER-945GSELVDS2 Page 133.1 Peripheral Interface Connectors The connectors on the WAFER-945GSELVDS2 are shown in the diagram below. Figure 3-1: Co

WAFER-945GSELVDS2Page 14 Connector Type Label Digital I/O connector 10-pin header DIO1 Fan connector 3-pin wafer CPU_FAN1 Keyboard and mouse c

WAFER-945GSELVDS2 Page 153.3 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when

WAFER-945GSELVDS2Page 16 CN Type: 3-pin wafer (1x3) CN Location: See Figure 3-3 CN Pinouts: See Table 3-4 Short pins 2-3 for AT power use, or connec

WAFER-945GSELVDS2 Page 17CN Pinouts: See Table 3-5 The 10-pin audio connector is connected to external audio devices including speakers and micropho

WAFER-945GSELVDS2 Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve

WAFER-945GSELVDS2Page 18 CN Label: BAT1 CN Type: 2-pin wafer (1x2) CN Location: See Figure 3-5 CN Pinouts: See Table 3-6 This is connected to the s

WAFER-945GSELVDS2 Page 19 Figure 3-6: CF Card Slot Location Pin Description Pin Description 1 GND 26 CD1# 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5

WAFER-945GSELVDS2Page 20 Pin Description Pin Description 16 A4 41 RESET# 17 A3 42 WAIT# 18 A2 43 INPACK# 19 A1 44 REG# 20 A0 45 BVD2 21 D0 46

WAFER-945GSELVDS2 Page 21 Figure 3-7: Digital I/O Connector Location Pin Description Pin Description 1 GND 2 VCC 3 Output 3 4 Output 2 5 Output 1

WAFER-945GSELVDS2Page 22 Figure 3-8: CPU Fan Connector Location Pin Description 1 GND 2 +12V 3 Fan Speed Detect Table 3-9: CPU Fan Connector Pino

WAFER-945GSELVDS2 Page 23 Figure 3-9: Keyboard/Mouse Connector Location Pin Description 1 VCC (+5 V) 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUN

WAFER-945GSELVDS2Page 24 Figure 3-10: LED Connector Locations Pin Description 1 +5V 2 GND 3 Power LED+ 4 Power LED- 5 HDD LED+ 6 HDD LED- Table 3-

WAFER-945GSELVDS2 Page 25 Figure 3-11: LVDS1 Location Pin Description Pin Description 1 GND1 2 GND2 3 A_Y0 4 A_Y0# 5 A_Y1 6 A_Y1# 7 A_Y2 8 A_Y2

WAFER-945GSELVDS2Page 26 3.3.11 LVDS1 Inverter Connector CN Label: INVERTER1 CN Type: 5-pin wafer (1x5) CN Location: See Figure 3-12 CN Pinouts: Se

WAFER-945GSELVDS2 Page 27CN Pinouts: See Table 3-14 The 18-bit, dual-channel LVDS connector can be attached to any compatible LVDS monitor. Figure

WAFER-945GSELVDS2Page iv Table of Contents 1 INTRODUCTION...

WAFER-945GSELVDS2Page 28 Pin Description Pin Description 29 VCC_LCD 30 VCC_LCD Table 3-14: LVDS2 Pinouts 3.3.13 LVDS2 Inverter Connector CN Label:

WAFER-945GSELVDS2 Page 29Pin Description 5 BACKLIGHT Enable Table 3-15: Backlight Connector Pinouts 3.3.14 PCIe Mini Card Slot CN Label: CN4 CN Typ

WAFER-945GSELVDS2Page 30 Pin Description Pin Description 7 CLKREQ# 8 N/C 9 GND 10 N/C 11 CLK- 12 N/C 13 CLK+ 14 N/C 15 GND 16 N/C 17 N/C

WAFER-945GSELVDS2 Page 31Turns the system on and off when the system is set to ATX power mode. Figure 3-16: Power Button Connector Location Pin De

WAFER-945GSELVDS2Page 32 Figure 3-17: Reset Button Connector Locations Pin Description 1 Reset Switch 2 GND Table 3-18: Reset Button Connector Pin

WAFER-945GSELVDS2 Page 33 Figure 3-18: SATA Drive Connector Locations Pin Description 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 3-19: SATA Dr

WAFER-945GSELVDS2Page 34 Figure 3-19: Serial Port Connector Location Pin Description Pin Description 1 DCD# 2 DSR# 3 RXD 4 RTS# 5 TXD 6 CT

WAFER-945GSELVDS2 Page 35 Figure 3-20: RS-232/422/485 Serial Port Connector Location Pin Description Pin Description 1 DCD# 2 DSR# 3 RXD 4 RT

WAFER-945GSELVDS2Page 36 The 2x4 USB pin connectors each provide connectivity to two USB 1.1 or two USB 2.0 ports. Each USB connector can support tw

WAFER-945GSELVDS2 Page 373.4.1 LAN Connectors CN Label: LAN1 CN Type: RJ-45 CN Location: See Figure 3-22 CN Pinouts: See Table 3-23 The WAFER-945GS

WAFER-945GSELVDS2 Page v3.3.11 LVDS1 Inverter Connector... 26 3.3.12 LVDS2

WAFER-945GSELVDS2Page 38 3.4.2 Serial Port Connector CN Label: COM1 CN Type: DB-9 connectors CN Location: See Figure 3-22 CN Pinouts: See Table 3-2

WAFER-945GSELVDS2 Page 39Pin Description Pin Description 1 VCC (+5V) 5 VCC (+5V) 2 DATA4- 6 DATA5- 3 DATA4+ 7 DATA5+ 4 GND 8 GND Table 3-26: USB

WAFER-945GSELVDS2Page 40 Chapter 4 4 Installation

WAFER-945GSELVDS2 Page 414.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the WAFER-945GSELVDS2 may

WAFER-945GSELVDS2Page 42 4.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read an

WAFER-945GSELVDS2 Page 43 Turn all power to the WAFER-945GSELVDS2 off: o When working with the WAFER-945GSELVDS2, make sure that it is disconnect

WAFER-945GSELVDS2Page 44 4.3 Unpacking When the WAFER-945GSELVDS2 is unpacked, please check all the unpacking list items listed in Chapter 3 are ind

WAFER-945GSELVDS2 Page 45Step 3: Insert the SO-DIMM. Push the SO-DIMM chip into the socket at an angle. (See Figure 4-1) Step 4: Open the SO-DIMM

WAFER-945GSELVDS2Page 46 Figure 4-2: CF Card Installation 4.6 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circu

WAFER-945GSELVDS2 Page 47Before the WAFER-945GSELVDS2 is installed in the system, the jumpers must be set in accordance with the desired configurati

WAFER-945GSELVDS2Page vi 4.7.2 Motherboard Installation... 56 4.8 INTE

WAFER-945GSELVDS2Page 48 Pin Description Open Use ATX power Table 4-2: AT Power Select Jumper Settings The location of the AT Power Select jumper is

WAFER-945GSELVDS2 Page 49The location of the audio power source selection jumper is shown below. Figure 4-4: Audio Power Source 4.6.3 CF Card Setup

WAFER-945GSELVDS2Page 50 Figure 4-5: CF Card Setup Jumper Location 4.6.4 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header Jumper

WAFER-945GSELVDS2 Page 51Pin Description 1-2 Keep CMOS Setup 2-3 Clear CMOS Setup Table 4-5: Clear CMOS Jumper Settings The location of the clear

WAFER-945GSELVDS2Page 52 Figure 4-7: COM 2 Function Select Jumper Location 4.6.6 LVDS1 and LVDS2 Panel Resolution Jumper Jumper Label: J_LCD_TYPE1

WAFER-945GSELVDS2 Page 53 Figure 4-8:LVDS Panel Resolution Jumper Pinout Locations 4.6.7 LVDS1 Voltage Selection WARNING: Permanent damage to the s

WAFER-945GSELVDS2Page 54 The LVDS1 Voltage Selection jumper location. is shown in Figure 4-9. Figure 4-9: LVDS1 Voltage Selection Jumper Pinout Loc

WAFER-945GSELVDS2 Page 55 Figure 4-10: LVDS Voltage Selection Jumper Pinout Locations 4.7 Chassis Installation 4.7.1 Airflow WARNING: Airflow is cr

WAFER-945GSELVDS2Page 56 4.7.2 Motherboard Installation To install the WAFER-945GSELVDS2 motherboard into the chassis please refer to the reference

WAFER-945GSELVDS2 Page 57 Figure 4-11: Audio Kit Cable Connection Step 3: Connect the audio devices. Connect speakers to the line-out audio jack.

WAFER-945GSELVDS2 Page vii5.4 PCI/PNP...

WAFER-945GSELVDS2Page 58 Step 2: Insert the cable connector. Press the clip on the connector at the end of the SATA cable and insert the cable conn

WAFER-945GSELVDS2 Page 59 Figure 4-13: SATA Power Drive Connection 4.8.3 RS-232 Cable Connection The dual RS-232 cable consists of two connectors at

WAFER-945GSELVDS2Page 60 Figure 4-14: Dual RS-232 Cable Installation Step 3: Secure the connectors. Both single RS-232 connectors have two retenti

WAFER-945GSELVDS2 Page 61Step 3: Insert the cable connectors. Once the cable connector is properly aligned with the keyboard/mouse connector on the

WAFER-945GSELVDS2Page 62 4.8.5 USB Cable The WAFER-945GSELVDS2 is shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please

WAFER-945GSELVDS2 Page 634.9 External Peripheral Interface Connection This section outlines the installation of devices to the external ports on the

WAFER-945GSELVDS2Page 64 4.9.2 Serial Device Connection The WAFER-945GSELVDS2 has a single female DB-9 connector on the external peripheral interfac

WAFER-945GSELVDS2 Page 65Step 1: Locate the USB Series "A" receptacle connectors. The location of the USB Series "A" receptacle

WAFER-945GSELVDS2Page 66 Step 3: Insert the VGA connector. Once the connectors are properly aligned with the insert the male connector from the VGA

WAFER-945GSELVDS2 Page 67 WARNING: When running the WAFER-945GSELVDS2, do not put the WAFER-945GSELVDS2 directly on a surface that can not dissipate

WAFER-945GSELVDS2Page viii List of Figures Figure 1-1: WAFER-945GSELVDS2...

WAFER-945GSELVDS2Page 68 Step 1: Insert the CD-ROM that came with the system into a CD-ROM drive attached to the system. Step 2: The screen in Fig

WAFER-945GSELVDS2 Page 69Step 3: Select the operating system. Figure 4-23: Select Operating System Step 4: Install all the drivers from the list.

WAFER-945GSELVDS2Page 70 Chapter 5 5 BIOS

WAFER-945GSELVDS2 Page 715.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system setting

WAFER-945GSELVDS2Page 72 Key Function F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS chan

WAFER-945GSELVDS2 Page 735.2 Main The Main BIOS menu appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic sy

WAFER-945GSELVDS2Page 74 The System Overview field also has two user configurable fields:  System Time [xx:xx:xx] Use the System Time option to se

WAFER-945GSELVDS2 Page 755.3.1 CPU Configuration Use the CPU Configuration menu to view detailed CPU specifications and configure the CPU. BIOS SETU

WAFER-945GSELVDS2Page 76 5.3.2 IDE Configuration Use the IDE Configuration menu to change and/or set the configuration of the IDE devices installed

WAFER-945GSELVDS2 Page 77 Legacy IDE Channels [PATA Pri, SATA Sec] Î SATA Only Only the SATA drives are enabled. Î PATA Pri, SATA Sec DEFAULTTh

WAFER-945GSELVDS2 Page ixFigure 3-25: VGA Connector ...

WAFER-945GSELVDS2Page 78  Auto-Detected Drive Parameters The “grayed-out” items in the left frame are IDE disk drive parameters automatically dete

WAFER-945GSELVDS2 Page 79Î CD/DVD The CD/DVD option specifies that an IDE CD-ROM drive is attached to the specified IDE channel. The BIOS does not

WAFER-945GSELVDS2Page 80  PIO Mode [Auto] Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing cycles between the

WAFER-945GSELVDS2 Page 81Î UDMA2 Ultra DMA mode 2, max transfer rate: 33.3 MB/s Î UDMA3 Ultra DMA mode 3, max transfer rate: 44 MB/s (To use this

WAFER-945GSELVDS2Page 82 5.3.3 Super IO Configuration Use the Super IO Configuration menu to set or change the configurations for the FDD controller

WAFER-945GSELVDS2 Page 83 Serial Port3 Address [3E8] Sets the address of serial port .  Disabled  3E8 DEFAULT  2E8  2F0  2E0  Serial Port3

WAFER-945GSELVDS2Page 84 5.3.4 Hardware Health Configuration The Hardware Health Configuration menu shows the operating temperature, fan speeds and

WAFER-945GSELVDS2 Page 85 CPU Temperature Limit of OFF [000] WARNING: CPU failure can result if this value is set too high because the fan will t

WAFER-945GSELVDS2Page 86  0.125 PWM  0.25 PWM  0.5 PWM  1 PWM  2 PWM  4 PWM  8 PWM  15 PWM 5.3.5 Power Configuration The Power Configuration

WAFER-945GSELVDS2 Page 87 Current Jumper Setting Displays the current power jumper setting. 5.3.5.1 ACPI configuration The ACPI Configuration menu