Iei-integration WAFER-945GSE2 v1.03 Manual de usuario

WAFER-945GSE2 User Manual Page itiWAFER-945GSE2 WAFER-945GSE23.5" SBC with 1.6 GHz Intel®Atom N270, VGA/LVDS, Dual GbE, CFII, USB, SATA, on b

WAFER-945GSE2 User ManualPage x E.4 MEMORY...

WAFER-945GSE2 User Manual Page 836.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows user

WAFER-945GSE2 User ManualPage 84 F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from tota

WAFER-945GSE2 User Manual Page 856.2 Main The Main BIOS menu (8BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an o

WAFER-945GSE2 User ManualPage 86 Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.  System Date [x

WAFER-945GSE2 User Manual Page 87BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (873H868HBIOS Menu 3) to view detailed

WAFER-945GSE2 User ManualPage 88  Frequency: Lists the CPU processing speed  FSB Speed: Lists the FSB speed  Cache L1: Lists the CPU L1 cache

WAFER-945GSE2 User Manual Page 89storage devices. Some legacy OS do not support this mode.  Legacy IDE Channels [PATA Pri, SATA Sec]  SATA Only

WAFER-945GSE2 User ManualPage 90 BIOS Menu 5: IDE Master and IDE Slave Configuration  Auto-Detected Drive Parameters The “grayed-out” items in th

WAFER-945GSE2 User Manual Page 91 32Bit Data Transfer: Enables 32-bit data transfer.  Type [Auto] Use the Type BIOS option select the type of de

WAFER-945GSE2 User ManualPage 92  Block (Multi Sector Transfer) [Auto] Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto det

WAFER-945GSE2 User Manual Page xiList of Figures Figure 1-1: WAFER-945GSE2 ...

WAFER-945GSE2 User Manual Page 93 Auto DEFAULT BIOS auto detects the DMA mode. Use this value if the IDE disk drive support cannot be determined. 

WAFER-945GSE2 User ManualPage 94 Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART

WAFER-945GSE2 User Manual Page 95Use the Serial Port1 Address option to select the Serial Port 1 base address.  Disabled No base address is ass

WAFER-945GSE2 User ManualPage 96 BIOS Menu 7: Hardware Health Configuration  CPU FAN Mode Setting [Full On Mode] Use the CPU FAN Mode Setting opt

WAFER-945GSE2 User Manual Page 97 CPU Temp. Limit of OFF [000] WARNING: Setting this value too high may cause the fan to stop when the CPU is at

WAFER-945GSE2 User ManualPage 98  CPU Fan Start PWM [070] The Fan 3 Start PWM option can only be set if the CPU FAN Mode Setting option is set to

WAFER-945GSE2 User Manual Page 99o CPU Core o +1.05V o +3.30V o +12.0 V o +1.5V o +1.8V o 5VSB o VBAT 6.3.5 Power Configuration Use the Powe

WAFER-945GSE2 User ManualPage 100 BIOS Menu 9: Advanced Power Configuration 6.3.5.1 ACPI configuration The ACPI Configuration menu (880H877HBIOS Men

WAFER-945GSE2 User Manual Page 101 S1 (POS) DEFAULT System appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power

WAFER-945GSE2 User ManualPage 102 Use the Power Button Mode BIOS to specify how the power button functions.  On/Off DEFAULT When the power button i

WAFER-945GSE2 User ManualPage xii Figure 4-14: PC/104 Power Input Connector Pinouts ...4

WAFER-945GSE2 User Manual Page 103activity  Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system shoul

WAFER-945GSE2 User ManualPage 104 BIOS Menu 12: Remote Access Configuration [Advanced]  Remote Access [Disabled] Use the Remote Access option to e

WAFER-945GSE2 User Manual Page 105Use the Serial Port Number option to select the serial port to use for remote access.  COM1 DEFAULT System is rem

WAFER-945GSE2 User ManualPage 106  Redirection After BIOS POST [Always] Use the Redirection After BIOS POST option to specify when console redirec

WAFER-945GSE2 User Manual Page 107Use the Sredir Memory Display Delay option to select the delay before memory information is displayed. Configurati

WAFER-945GSE2 User ManualPage 108  Disabled USB function disabled  Enabled DEFAULT USB function enabled  USB2.0 Controller Mode [HiSpeed] The U

WAFER-945GSE2 User Manual Page 109menu may cause the system to malfunction. BIOS Menu 14: PCI/PnP Configuration  IRQ# [Available] Use the IRQ#

WAFER-945GSE2 User ManualPage 110  IRQ 14  IRQ 15  DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a pa

WAFER-945GSE2 User Manual Page 111BIOS Menu 15: Boot 6.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (886H883HBIOS Menu 1

WAFER-945GSE2 User ManualPage 112  Disabled No POST procedures are skipped  Enabled DEFAULT Some POST procedures are skipped to decrease the sys

WAFER-945GSE2 User Manual Page xiiiFigure 7-7: Chipset Driver Setup Operations ...

WAFER-945GSE2 User Manual Page 113Lock LED light on the keyboard is lit.  Boot From LAN Support [Disabled] The BOOT From LAN Support option enable

WAFER-945GSE2 User ManualPage 114 BIOS Menu 18: Security  Change Supervisor Password Use the Change Supervisor Password to set or change a supervi

WAFER-945GSE2 User Manual Page 115menu may cause the system to malfunction. BIOS Menu 19: Chipset 6.7.1 Northbridge Chipset Configuration Use the

WAFER-945GSE2 User ManualPage 116 The Memory Hole reserves the memory space between 15MB and 16MB for ISA expansion cards that require a specified

WAFER-945GSE2 User Manual Page 117Use the DVMT/FIXED Memory option to specify the maximum amount of memory that can be allocated as graphics memory.

WAFER-945GSE2 User ManualPage 118 BIOS Menu 21:Southbridge Chipset Configuration  Audio Controller [All Disabled] The Audio Controller option ena

WAFER-945GSE2 User Manual Page 119 BIOS Menu 22:Exit  Save Changes and Exit Use the Save Changes and Exit option to save the changes made to t

WAFER-945GSE2 User ManualPage 120 Chapter 7 7 Software Drivers

WAFER-945GSE2 User Manual Page 1217.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and

WAFER-945GSE2 User ManualPage 122 Step 2: The screen in 896HFigure 7-1 appears. Figure 7-1: Start Up Screen Step 3: Click NANO-ATOM. Step 4: The

WAFER-945GSE2 User ManualPage xiv Figure 7-42: iSMM InstallShield Wizard Complete ...

WAFER-945GSE2 User Manual Page 123Step 6: The list of drivers in 898HFigure 7-3 appears.Step 0: Figure 7-3: Drivers 7.3 Chipset Driver Installatio

WAFER-945GSE2 User ManualPage 124 Figure 7-4: Chipset Driver Welcome Screen Step 4: Click NEXT to continue. Step 5: The license agreement in 902HF

WAFER-945GSE2 User Manual Page 125Step 7: Click the YES button to accept the license agreement and continue. Step 8: The Read Me file in 903HFigur

WAFER-945GSE2 User ManualPage 126 Figure 7-7: Chipset Driver Setup Operations Step 11: Once the Setup Operations are complete, click the NEXT icon t

WAFER-945GSE2 User Manual Page 127Step 13: Select “Yes, I want to restart the computer now” and click the Finish icon. See 905HFigure 7-8.Step 0: 7.

WAFER-945GSE2 User ManualPage 128 Figure 7-10: VGA Driver Setup Files Extracted Step 6: The Welcome Screen in 910HFigure 7-11 appears. Figure 7-11:

WAFER-945GSE2 User Manual Page 129Figure 7-12: VGA Driver License Agreement Step 9: Read the License Agreement. Step 10: Click YES to accept the l

WAFER-945GSE2 User ManualPage 130 Step 12: Click NEXT to continue. Step 13: Setup Operations are performed as shown in 913HFigure 7-14. NOTE: The “

WAFER-945GSE2 User Manual Page 131Figure 7-15: VGA Driver Installation Finish Screen Step 16: Select “Yes, I want to restart the computer now” and c

WAFER-945GSE2 User ManualPage 132 Figure 7-16: LAN Driver Welcome Screen Step 4: Click NEXT to continue. Step 5: The Ready to Install screen in 91

WAFER-945GSE2 User Manual Page xvList of Tables Table 1-1: Technical Specifications...

WAFER-945GSE2 User Manual Page 133Step 8: The installation progress can be monitored in the progress bar shown in 919HFigure 7-18. Figure 7-18: LAN

WAFER-945GSE2 User ManualPage 134 7.6 Audio Driver Installation There is no audio driver on the WAFER-945GSE2. To add audio capabilities to the WAFE

WAFER-945GSE2 User Manual Page 135Step 3: Browse to “E:\4-Audio\ALC665\Windows\Windows 98Gold, 98se, Me, 2000, XP, 2003(32,64 bits)\A3.84” 924HFigu

WAFER-945GSE2 User ManualPage 136 Step 7: The Verification window in 927HFigure 7-23 may appear. Figure 7-23: AC’97 Driver Installation Verificatio

WAFER-945GSE2 User Manual Page 137Step 10: Select “Yes, I wish to restart my computer now” And click FINISH to exit the InstallShield Wizard and re

WAFER-945GSE2 User ManualPage 138 Figure 7-26: SATA RAID Driver Installation Program Step 5: Double-click the IATA85CD.exe program icon in 932HFigu

WAFER-945GSE2 User Manual Page 139Figure 7-28: InstallShield Wizard Setup Screen Step 7: 934HFigure 7-29 shows the Matrix Storage Manager software c

WAFER-945GSE2 User ManualPage 140 Figure 7-30: Matrix Storage Manager Welcome Screen Step 9: Click NEXT and a warning appears (936HFigure 7-31). Re

WAFER-945GSE2 User Manual Page 141Figure 7-32: Matrix Storage Manager License Agreement Step 11: Read the license agreement. To accept the terms and

WAFER-945GSE2 User ManualPage 142 Step 13: After the driver installation process is complete, a confirmation screen appears (939HFigure 7-34). Figur

WAFER-945GSE2 User ManualPage xvi Table 5-4: Clear CMOS Jumper Settings...

WAFER-945GSE2 User Manual Page 143Figure 7-35: iSMM Directory Step 4: Double click the iSMM EN V1.11.00 directory icon. (943HFigure 7-35) Step 5:

WAFER-945GSE2 User ManualPage 144 Step 7: The iSMM InstallShield Welcome Screen appears. (946HFigure 7-37) Figure 7-37: iSMM InstallShield Welcome

WAFER-945GSE2 User Manual Page 145Step 10: Select “I accept the terms of the license agreement.” (948HFigure 7-38) Step 11: Click NEXT to continue.(

WAFER-945GSE2 User ManualPage 146 Step 15: The Setup Type screen appears. (953HFigure 7-40) Figure 7-40: iSMM Setup Type Step 16: Select “Complete”

WAFER-945GSE2 User Manual Page 147Step 18: The Installation Confirmation screen appears. (956HFigure 7-41) Figure 7-41: iSMM Installation Confirmati

WAFER-945GSE2 User ManualPage 148 Step 20: The InstallShield Wizard Completed appears when the drivers are finished installing. (958HFigure 7-42) Fi

WAFER-945GSE2 User Manual Page 149Appendix A A BIOS Options

WAFER-945GSE2 User ManualPage 150 Below is a list of BIOS configuration options in the BIOS chapter. 346H　 System Overview ...

WAFER-945GSE2 User Manual Page 151379H　 Serial Port Number ...

WAFER-945GSE2 User ManualPage 152 414H　 Save Changes and Exit ...

WAFER-945GSE2 User Manual Page xviiBIOS Menus Menu 1: Main...

WAFER-945GSE2 User Manual Page 153Appendix B B Terminology

WAFER-945GSE2 User ManualPage 154 AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration

WAFER-945GSE2 User Manual Page 155DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate dire

WAFER-945GSE2 User ManualPage 156 LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a

WAFER-945GSE2 User Manual Page 157Appendix C C Digital I/O Interface

WAFER-945GSE2 User ManualPage 158 C.1 Introduction The DIO connector on the WAFER-945GSE2 is interfaced to GPIO ports on the Super I/O chipset. The

WAFER-945GSE2 User Manual Page 159C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the dig

WAFER-945GSE2 User ManualPage 160 Appendix D D Watchdog Timer

WAFER-945GSE2 User Manual Page 161 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited fo

WAFER-945GSE2 User ManualPage 162 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE

WAFER-945GSE2 User Manual Page 1Chapter 1 1 Introduction

WAFER-945GSE2 User Manual Page 163Appendix E E Address Mapping

WAFER-945GSE2 User ManualPage 164 E.1 Direct Memory Access (DMA) Figure E-1: Direct Memory Access (DMA)

WAFER-945GSE2 User Manual Page 165E.2 Input/Output (IO) Figure E-2: Input/Output (IO) (1 of 2)

WAFER-945GSE2 User ManualPage 166 Figure E-3: Input/Output (IO) (2 of 2)

WAFER-945GSE2 User Manual Page 167E.3 Interrupt Request (IRQ) Figure E-4: Interrupt Request (IRQ)

WAFER-945GSE2 User ManualPage 168 E.4 Memory Figure E-5: Memory

WAFER-945GSE2 User Manual Page 169Appendix F F Compatibility

WAFER-945GSE2 User ManualPage 170 NOTE: The compatible items described here have been tested by the IEI R&D team and found to be compatible wit

WAFER-945GSE2 User Manual Page 171F.3 Compatible Memory Modules NOTE: The memory modules listed below have been tested on the WAFER-945GSE2 other m

WAFER-945GSE2 User ManualPage 172 Appendix G G Hazardous Materials Disclosure

WAFER-945GSE2 User ManualPage 2 1.1 Overview Figure 1-1: WAFER-945GSE2 1.1.1 WAFER-945GSE2 Introduction WAFER-945GSE2 3.5” motherboards are embedded

WAFER-945GSE2 User Manual Page 173G.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mer

WAFER-945GSE2 User ManualPage 174 Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium(Cd) Hexavalent Chromium(CR(VI)

WAFER-945GSE2 User Manual Page 175此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含

WAFER-945GSE2 User ManualPage 176 Appendix H H AC'97 Audio Codec

WAFER-945GSE2 User Manual Page 177H.1 Introduction The motherboard comes with an onboard Realtek ALC655 CODEC. The ALC655 is a 16-bit, full-duplex A

WAFER-945GSE2 User ManualPage 178 Figure H-1: Control Panel Sound Effect Manager H.2 Sound Effect Configuration H.2.1 Accessing the Sound Effects Ma

WAFER-945GSE2 User Manual Page 179Figure H-3: Sound Effects Manager (ALC655) NOTE: The Sound Effect Manager shown in 1037HFigure H-3 is for the Re

WAFER-945GSE2 User ManualPage 180  Sound Effect  Karaoke Mode  Equalizer  Speaker Configuration  Speaker Test  S/PDIF-In  S/PDIF-Out  Co

WAFER-945GSE2 User Manual Page 181o Channel mode for 5.1 speaker output o Synchronize the phone jack switch with speakers settings  Speaker Te

WAFER-945GSE2 User ManualPage 182 Index

WAFER-945GSE2 User ManualPage ii Revision Date Version Changes 20 September, 2011 1.03 Updated section 2.2 Data Flow 25 June, 2009 1.02 New phot

WAFER-945GSE2 User Manual Page 3Figure 1-2: WAFER-945GSE2 Overview [Front View] 1.2.2 WAFER-945GSE2 Peripheral Connectors and Jumpers The WAFER-945G

WAFER-945GSE2 User Manual Page 183 4 4-port RS-232 serial port connector ...4 A ACPI ...99,

WAFER-945GSE2 User ManualPage 184 RS-232, RS-422 or RS-485 ...51 COM 2 function select jumper ...51, 66 location ...

WAFER-945GSE2 User Manual Page 185H hard disk drives SATA...50 HDD ...

WAFER-945GSE2 User ManualPage 186 dual channel...45 single channel ...45

WAFER-945GSE2 User Manual Page 187cables ...70 connection ...

WAFER-945GSE2 User ManualPage 4  1 x RS-232 serial port connector  2 x Serial ATA (SATA) drive connectors  2 x USB 2.0 connectors (supports fo

WAFER-945GSE2 User Manual Page 5Display Intel® Generation 3.5 integrated GFX core (133 MHz) 18-bit dual channel LVDS integrated in Intel® 945GSE D

WAFER-945GSE2 User ManualPage 6 Chapter 2 2 Detailed Specifications

WAFER-945GSE2 User Manual Page 72.1 Dimensions 2.1.1 Board Dimensions The dimensions of the board are shown below: Figure 2-1: WAFER-945GSE2 Dimensi

WAFER-945GSE2 User ManualPage 8 2.2 Data Flow 7Figure 2-3 shows the data flow between the two on-board chipsets and other components installed on th

WAFER-945GSE2 User Manual Page 92.3 Embedded WAFER-945GSE2 Processor 2.3.1 Overview The WAFER-945GSE2 comes with an embedded 45 nm 1.60 GHz Intel® A

WAFER-945GSE2 User ManualPage 10  Thermal management support via Intel® Thermal Monitor 1 and Intel® Thermal Monitor 2  FSB Lane Reversal for fl

WAFER-945GSE2 User Manual Page 112.4 Intel®945GSE Northbridge Chipset 2.4.1 Intel® 945GSE Overview The Intel® 945GSE Graphics and Memory Controller

WAFER-945GSE2 User ManualPage 12 Figure 2-6: Onboard DDR2 SDRAM 2.4.3 Intel® 945GSE Graphics The Intel® 945GSE supports CRT and LVDS. The internal g

WAFER-945GSE2 User Manual Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to

WAFER-945GSE2 User Manual Page 132.4.3.1 Analog CRT Graphics Mode The analog CRT bus is interfaced to an external DB-15 interface connector. The con

WAFER-945GSE2 User ManualPage 14 Figure 2-8: LVDS Connector Some of the features of the LVDS interface include:  Panel support up to UXGA (1600 x

WAFER-945GSE2 User Manual Page 15Figure 2-9: Direct Media Interface Some of the features of the Intel® ICH7-M are listed below.  Complies with PCI

WAFER-945GSE2 User ManualPage 16  Serial peripheral interface support 2.5.2 Intel® ICH7-M Audio Codec ’97 Controller The Integrated AC'97 v2.

WAFER-945GSE2 User Manual Page 17 Three analog line-level stereo inputs with 5-bit volume control, LINE_IN, CD, AUX  High-quality differential

WAFER-945GSE2 User ManualPage 18  PCI Revision 2.3 compliant  33MHz  5V tolerant PCI signals (except PME#)  Integrated PCI arbiter supports u

WAFER-945GSE2 User Manual Page 19 ISA Interface  SM Bus  One analog line-level mono output: MONO_OUT  Power-on Serial Bus Configuration  Ser

WAFER-945GSE2 User ManualPage 20 Figure 2-12: Realtek RTL8111CP PCIe GbE Controllers The Realtek RTL8111CP PCIe GbE controllers combine a triple-spe

WAFER-945GSE2 User Manual Page 21 Supports Full Duplex flow control (IEEE 802.3x)  Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

WAFER-945GSE2 User ManualPage 22 Figure 2-13: SATA Connectors SATA controller specifications are listed below.  Supports four SATA drives  Suppo

WAFER-945GSE2 User ManualPage iv Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with

WAFER-945GSE2 User Manual Page 23Figure 2-14: Onboard USB Implementation 2.6 LPC Bus Components 2.6.1 LPC Bus Overview The SIS964 LPC bus is connect

WAFER-945GSE2 User ManualPage 24 2.6.3 iTE IT8718F Super I/O chipset The iTE IT8718F Super I/O chipset is connected to the ICH7-M Southbridge throug

WAFER-945GSE2 User Manual Page 252.6.3.1 Super I/O LPC Interface The LPC interface on the Super I/O complies with the Intel® Low Pin Count Specifica

WAFER-945GSE2 User ManualPage 26 2.7 Environmental and Power Specifications 2.7.1 System Monitoring Two thermal inputs on the WAFER-945GSE2 Super I/

WAFER-945GSE2 User Manual Page 27A heat sink must be installed on the CPU, Northbridge and the front-side onboard memory. Thermal paste must be smea

WAFER-945GSE2 User ManualPage 28 Chapter 3 3 Unpacking

WAFER-945GSE2 User Manual Page 293.1 Anti-static Precautions WARNING! Failure to take ESD precautions during the installation of the WAFER-945GSE2

WAFER-945GSE2 User ManualPage 30 3.3 Unpacking Checklist NOTE: If any of the components listed in the checklist below are missing, do not proceed w

WAFER-945GSE2 User Manual Page 312 Plastic intermediate pole for PC/104 (20mm) 1 Utility CD 1 Quick Installation Guide 3.3.2 Optional Items The

WAFER-945GSE2 User ManualPage 32 Chapter 4 4 Connectors

WAFER-945GSE2 User Manual Page vTable of Contents 1 INTRODUCTION...

WAFER-945GSE2 User Manual Page 334.1 Peripheral Interface Connectors Section 4.1.1 shows the peripheral interface connector locations. Section 4.2 l

WAFER-945GSE2 User ManualPage 34 Figure 4-2: Connector and Jumper Locations [solder side] 4.2 Peripheral Interface Connectors 7Table 4-1 shows a lis

WAFER-945GSE2 User Manual Page 35Reset button connector 2-pin header RESET1 RS-232/422/485 serial port connector 14-pin header COM2 Serial ATA (S

WAFER-945GSE2 User ManualPage 36 4.3.1 ATX Power Connector CN Label: ATXPWR1 CN Type: 4-pin AT power connector (1x4) CN Location: See Figure 4-3 CN

WAFER-945GSE2 User Manual Page 37The ATX power supply enable connector enables the WAFER-945GSE2 to be connected to an ATX power supply. In default

WAFER-945GSE2 User ManualPage 38 Figure 4-5: Audio Connector Pinouts (10-pin) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 Line out R 2 Line in

WAFER-945GSE2 User Manual Page 39 Figure 4-6: Panel Backlight Connector Pinout Locations PIN NO. DESCRIPTION 1 LCD Backlight Control 2 GROUND 3 +1

WAFER-945GSE2 User ManualPage 40 Figure 4-7: CF Card Socket Location (solder side) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 26 CD1# 2 D

WAFER-945GSE2 User Manual Page 41PIN NO. DESCRIPTION PIN NO. DESCRIPTION 25 CD2# 50 GND2 Table 4-7: CF Card Socket Pinouts 4.3.6 Digital Input

WAFER-945GSE2 User ManualPage 42 4.3.7 Fan Connector (+12V, 3-pin) CN Label: CPU_FAN1 CN Type: 3-pin header CN Location: See 7Figure 4-9 CN Pinouts:

WAFER-945GSE2 User ManualPage vi 2.5.7 Intel® ICH7-M Real Time Clock ... 21 2.5.8

WAFER-945GSE2 User Manual Page 434.3.8 Keyboard/Mouse Connector CN Label: KB_MS1 CN Type: 6-pin header (1x6) CN Location: See Figure 4-10 CN Pinout

WAFER-945GSE2 User ManualPage 44 4.3.9 LED Connector CN Label: LED_C1 CN Type: 6-pin wafer (1x6) CN Location: See Figure 4-11 CN Pinouts: See Table

WAFER-945GSE2 User Manual Page 45CN Pinouts: See 7Table 4-12 The 30-pin LVDS LCD connector can be connected to single channel or dual channel, 24-bi

WAFER-945GSE2 User ManualPage 46 4.3.11 PC/104 Connector CN Label: CN2 CN Type: 104-pin PC/104 slot CN Location: See 7Figure 4-13 CN Pinouts: See

WAFER-945GSE2 User Manual Page 47PIN Description PIN Description PIN Description PIN Description A12 SA19 A28 SA3 B12 -SMEMR B28 BALE A13 S

WAFER-945GSE2 User ManualPage 48 Figure 4-14: PC/104 Power Input Connector Pinouts PIN NO. DESCRIPTION 1 -5V 2 GND 3 -12V Table 4-15: PC/104 Power

WAFER-945GSE2 User Manual Page 49PIN NO. DESCRIPTION 1 Power Switch 2 GND Table 4-16: Power Button Connector Pinouts 4.3.14 Reset Button Connector

WAFER-945GSE2 User ManualPage 50 4.3.15 SATA Drive Connectors CN Label: SATA1, SATA2 CN Type: 7-pin SATA drive connectors CN Location: See 8Figure 4

WAFER-945GSE2 User Manual Page 514.3.16 Serial Port Connector (COM2 ) (RS-232, RS-422 or RS-485) CN Label: COM2 CN Type: 14-pin header (2x7) CN Loc

WAFER-945GSE2 User ManualPage 52 4.3.17 USB Connectors (Internal) CN Label: USB01 and USB23 CN Type: 8-pin header (2x4) CN Location: See 8Figure 4

WAFER-945GSE2 User Manual Page vii4.3.4 Backlight Inverter Connector ... 38 4

WAFER-945GSE2 User Manual Page 534.4 External Peripheral Interface Connector Panel 8Figure 4-20 shows the WAFER-945GSE2 external peripheral interfac

WAFER-945GSE2 User ManualPage 54 4 MDIA1- 8 MDIA0+ Table 4-21: LAN Pinouts Figure 4-21: RJ-45 Ethernet ConnectorThe RJ-45 Ethernet connector has

WAFER-945GSE2 User Manual Page 55Table 4-23: RS-232 Serial Port (COM 1) Pinouts Figure 4-22: COM1 Pinout Locations4.4.3 USB Connectors CN Label: U

WAFER-945GSE2 User ManualPage 56 The WAFER-945GSE2 has a single 15-pin female connector for connectivity to standard display devices. Figure 4-23:

WAFER-945GSE2 User Manual Page 57Chapter 5 5 Installation

WAFER-945GSE2 User ManualPage 58 5.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the WAFER-945GSE2

WAFER-945GSE2 User Manual Page 595.1.1 Installation Notices WARNING: The installation instructions described in this manual should be carefully fol

WAFER-945GSE2 User ManualPage 60 5.1.2 Installation Checklist The following checklist is provided to ensure the WAFER-945GSE2 is properly installed.

WAFER-945GSE2 User Manual Page 61II cards. For the complete specifications of the supported CF cards please refer to Chapter 2. To install a CF card

WAFER-945GSE2 User ManualPage 62 5.4 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or

WAFER-945GSE2 User ManualPage viii 5.5.1 Airflow...

WAFER-945GSE2 User Manual Page 63Jumper Label: ATXCTl1 Jumper Type: 3-pin header Jumper Settings: See Table 5-2 Jumper Location: See Figure 5-3 The

WAFER-945GSE2 User ManualPage 64 5.4.2 CF Card Setup Jumper Label: JCF1 Jumper Type: 2-pin header Jumper Settings: See Table 5-3 Jumper Location: Se

WAFER-945GSE2 User Manual Page 65If the WAFER-945GSE2 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and re

WAFER-945GSE2 User ManualPage 66 Figure 5-5: Clear CMOS Jumper 5.4.4 COM 2 Function Select Jumper Jumper Label: JP1 Jumper Type: 8-pin header Jumpe

WAFER-945GSE2 User Manual Page 67 Figure 5-6: COM 2 Function Select Jumper Location5.4.5 LVDS Voltage Selection WARNING: Permanent damage to the sc

WAFER-945GSE2 User ManualPage 68 LCD Voltage Select Description Short 1-2 +3.3V LVDS Default Short 2-3 +5V LVDS Table 5-6: LVDS Voltage Se

WAFER-945GSE2 User Manual Page 69power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface. N

WAFER-945GSE2 User ManualPage 70  SATA power cable 5.6.2 SATA Drive Connection The WAFER-945GSE2 is shipped with two SATA drive cables. To connect

WAFER-945GSE2 User Manual Page 71 NOTE: The SATA power cable described below is an optional item and must be pre-ordered. The SATA power cable is no

WAFER-945GSE2 User ManualPage 72 the connector can only be installed in one direction. Figure 5-10: Dual RS-232 Cable Installation Step 3: Secure t

WAFER-945GSE2 User Manual Page ix6.4 PCI/PNP...

WAFER-945GSE2 User Manual Page 73Figure 5-11: Serial Device Connector 5.6.4 Keyboard/Mouse Y-cable Connector The WAFER-945GSE2 is shipped with a key

WAFER-945GSE2 User ManualPage 74 Figure 5-12: Keyboard/mouse Y-cable ConnectionStep 4: Attach PS/2 connectors to the chassis. The keyboard/mouse Y

WAFER-945GSE2 User Manual Page 75Step 1: Locate the audio connector. The location of the 10-pin audio connector is shown in Chapter 3. Step 2: Ali

WAFER-945GSE2 User ManualPage 76 Figure 5-14: WAFER-945GSE2 PC/104 module installation Step 1: Remove retention nuts. Remove the two nuts securing

WAFER-945GSE2 User Manual Page 77Chapter 3. WARNING: If the USB pins are not properly aligned, the USB device can burn out. Step 6: Align the conn

WAFER-945GSE2 User ManualPage 78  RJ-45 Ethernet cable connectors  Serial port devices  USB devices  VGA monitors To install these devices, co

WAFER-945GSE2 User Manual Page 79Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the o

WAFER-945GSE2 User ManualPage 80 5.7.3 USB Connection (Dual Connector) The external USB receptacle connectors provide easier and quicker access to

WAFER-945GSE2 User Manual Page 81Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen cable with the female DB-15 conn

WAFER-945GSE2 User ManualPage 82 Chapter 6 6 BIOS Screens