Iei-integration NANO-QM57A Manual de usuario

NANO-QM57A EPIC SBC Page IIEI Technology Corp. User Manual NANO-QM57AMODEL: EPIC Motherboard Supports Socket G1 Intel® Core™i3/i5/i7CPU, Dual DVI, G

NANO-QM57A EPIC SBCPage X Figure C-19: Partitions for Linux...

NANO-QM57A EPIC SBCPage 88 A.1 Intel® AMT Setup Procedure The NANO-QM57A is featured with the Intel® Active Management Technology (AMT) 6.0. To enab

NANO-QM57A EPIC SBC Page 89Step 2: Enter the Intel® ME password as it requires (Figure A-2). Enter the Intel® default password: admin. Intel(R) Man

NANO-QM57A EPIC SBCPage 90 Intel(R) Management Engine BIOS Extension v6.0.3.0019/Intel(R) ME v6.0.30.1203Copyright (C) 2003-09 Intel Corporation. Al

NANO-QM57A EPIC SBC Page 91Step 6: Select KVM Configuration and press Enter. (Figure A-5) Intel(R) Management Engine BIOS Extension v6.0.3.0019/Int

NANO-QM57A EPIC SBCPage 92 Step 8: Two options are shown as in Figure A-7. Choose User Consent is not required for KVM session which means no passw

NANO-QM57A EPIC SBC Page 93A.3 IEI Easy Manager Application IEI Easy Manager (iEZMan) application program allows a remote user, such as a support p

NANO-QM57A EPIC SBCPage 94 Appendix B B BIOS Menu Options 　 BIOS Information ...

NANO-QM57A EPIC SBC Page 95　 Segment 2 Speed Count [085]...

NANO-QM57A EPIC SBCPage 96 Appendix C C One Key Recovery

NANO-QM57A EPIC SBC Page 97C.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup

NANO-QM57A EPIC SBC Page XIList of Tables Table 1-1: Technical Specifications...

NANO-QM57A EPIC SBCPage 98 o Windows 7 o Windows CE 5.0 o Windows CE 6.0 o Windows XP Embedded  Linux o Fedora Core 12 (Constantine) o Fedora

NANO-QM57A EPIC SBC Page 99 NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appea

NANO-QM57A EPIC SBCPage 100 NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux system, most set

NANO-QM57A EPIC SBC Page 101 Figure C-1: Recovery Tool Setup Menu Step 5: Press <5> then <Enter>. Figure C-2: Command Mode Step 6: Th

NANO-QM57A EPIC SBCPage 102 system32>format F: /fs:ntfs /q /v:Recovery /y system32>exit Figure C-3: Partition Creation Commands

NANO-QM57A EPIC SBC Page 103 NOTE: Use the following commands to check if the partitions were created successfully. Step 7: Press any key to exit

NANO-QM57A EPIC SBCPage 104 Step 2: Start the system. Step 3: Press any key to boot from the recovery CD. It will take a while to launch the recov

NANO-QM57A EPIC SBC Page 105 Figure C-5: Build-up Recovery Partition Step 6: After completing the system configuration, press any key in the follow

NANO-QM57A EPIC SBCPage 106 C.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a fa

NANO-QM57A EPIC SBC Page 107 Figure C-9: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure C-10). Figur

NANO-QM57A EPIC SBCPage XII List of BIOS Menus BIOS Menu 1: Main ...

NANO-QM57A EPIC SBCPage 108 Figure C-11: Select a Local Source Drive Step 6: Select a source partition from basic drive as shown in Figure A-4. The

NANO-QM57A EPIC SBC Page 109 Figure C-13: File Name to Copy Image to Step 8: When the Compress Image screen in Figure A-6 prompts, click High to ma

NANO-QM57A EPIC SBCPage 110 Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure C-15: Image Creation C

NANO-QM57A EPIC SBC Page 111Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step 0: Figure C

NANO-QM57A EPIC SBCPage 112 NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure C-19: Partitions for Linux Step

NANO-QM57A EPIC SBC Page 113recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD

NANO-QM57A EPIC SBCPage 114 Step 7: The recovery tool menu appears. (Figure C-22) Figure C-22: Recovery Tool Menu Step 8: Create a factory defau

NANO-QM57A EPIC SBC Page 115Figure C-23: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the

NANO-QM57A EPIC SBCPage 116 C.4.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and p

NANO-QM57A EPIC SBC Page 117C.4.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press <Enter>

NANO-QM57A EPIC SBC Page 1 1 Introduction Chapter 1

NANO-QM57A EPIC SBCPage 118 C.4.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3>

NANO-QM57A EPIC SBC Page 119C.4.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press <Ent

NANO-QM57A EPIC SBCPage 120 Appendix D D Terminology

NANO-QM57A EPIC SBC Page 121 AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and

NANO-QM57A EPIC SBCPage 122 computer is usually a male DE-9 connector. DAC The Digital-to-Analog Converter (DAC) converts digital signals to analog

NANO-QM57A EPIC SBC Page 123PCIe PCI Express (PCIe) is a communications bus that uses dual data lines for full-duplex (two-way) serial (point-to-po

NANO-QM57A EPIC SBCPage 124 USB 2.0 supports 480Mbps data transfer rates. VGA The Video Graphics Array (VGA) is a graphics display system developed

NANO-QM57A EPIC SBC Page 125Appendix E E Watchdog Timer

NANO-QM57A EPIC SBCPage 126 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for

NANO-QM57A EPIC SBC Page 127 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Example prog

NANO-QM57A EPIC SBCPage 2 1.1 Introduction Figure 1-1: NANO-QM57A The NANO-QM57A EPIC motherboard is a Socket G1 32nm Intel® Core™ i3, i5 and i7 pr

NANO-QM57A EPIC SBCPage 128 Appendix F F Hazardous Materials Disclosure

NANO-QM57A EPIC SBC Page 129F.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury Th

NANO-QM57A EPIC SBCPage 130 Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (CR(VI)) P

NANO-QM57A EPIC SBC Page 131此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境

NANO-QM57A EPIC SBC Page 3 Figure 1-2: Connectors 1.3 Dimensions The dimensions of the board are listed below:  Length: 165 mm

NANO-QM57A EPIC SBCPage 4  Width: 115 mm Figure 1-3: NANO-QM57A Dimensions (mm)

NANO-QM57A EPIC SBC Page 51.4 Data Flow 5Figure 1-4 shows the data flow between the two on-board chipsets and other components installed on the moth

NANO-QM57A EPIC SBCPage 6 1.5 Technical Specifications NANO-QM57A technical specifications are listed in table below. Specification NANO-QM57A Form

NANO-QM57A EPIC SBC Page 7Specification NANO-QM57A Serial ATA Two SATA 3.0 Gb/s connectors with RAID 0,1 support Two 5V SATA power connectors Envir

NANO-QM57A EPIC SBCPage II Revision Date Version Changes 16 August, 2011 1.01 Modified operating temperature information 9 July, 2010 1.00 Initi

NANO-QM57A EPIC SBCPage 8 2 Unpacking Chapter 2

NANO-QM57A EPIC SBC Page 92.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD prec

NANO-QM57A EPIC SBCPage 10 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the insta

NANO-QM57A EPIC SBC Page 111 Utility CD 1 Quick Installation Guide 2.3.1 Optional Items The following are optional components which may be separa

NANO-QM57A EPIC SBCPage 12 3 Connectors Chapter 3

NANO-QM57A EPIC SBC Page 133.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 NANO-QM57A Layout The fig

NANO-QM57A EPIC SBCPage 14 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label Audi

NANO-QM57A EPIC SBC Page 15 The table below lists the connectors on the external I/O panel. Connector Type Label Ethernet connector RJ-45 LAN1

NANO-QM57A EPIC SBCPage 16 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 LFRONT-R 2 LLINE-R 3 GND 4 GND 5 LFRONT-L 6 LLINE-L 7 GND 8 GND 9 LMIC1-C

NANO-QM57A EPIC SBC Page 17Pin Description 1 Battery+ 2 Ground Table 3-4: Battery Connector Pinouts 3.2.3 BIOS Update Connector CN Label: JSPI1 CN

NANO-QM57A EPIC SBC Page IIICopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improv

NANO-QM57A EPIC SBCPage 18 CN Location: See Figure 3-5 CN Pinouts: See Table 3-6 The fan connector attaches to a CPU cooling fan. Figure 3-5: CPU F

NANO-QM57A EPIC SBC Page 19 Figure 3-6: +12V Fan Connector Locations PIN NO. DESCRIPTION 1 N/C 2 +12V 3 GND Table 3-7: +12V Fan Connector Pinouts

NANO-QM57A EPIC SBCPage 20 Figure 3-7: Front Panel Connector Location FUNCTION PIN DESCRIPTION FUNCTION PIN DESCRIPTION 1 PWRBTN_SW# 2 PWR LED

NANO-QM57A EPIC SBC Page 21 Pin Description 1 +5 VCC 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUND Table 3-9: Keyboard/Mouse Connector Pinouts 3.2.

NANO-QM57A EPIC SBCPage 22 Pin Description Pin Description 13 CLK+ 14 LAD1 15 GND 16 LAD0 17 PCIRST# 18 GND 19 LPC 20 VCC3 21 GND 22 PCIRST# 2

NANO-QM57A EPIC SBC Page 23 Figure 3-10: CPU 12V Power Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION1 GND 2 GND 3 +12V 4 +12V Tab

NANO-QM57A EPIC SBCPage 24 PIN NO. DESCRIPTION 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 3-12: SATA Drive Connector Pinouts3.2.11 SATA Power

NANO-QM57A EPIC SBC Page 253.2.12 Serial Port Connectors (RS-232) CN Label: COM1 and COM2 CN Type: 10-pin header (2x5) CN Location: See 5Figure 3-13

NANO-QM57A EPIC SBCPage 26 The USB connectors connect to USB devices. Each pin header provides two USB ports. Figure 3-14: USB Connector Pinout Loc

NANO-QM57A EPIC SBC Page 27 Figure 3-15: NANO-QM57A External Peripheral Interface Connector 3.3.1 DVI Connector CN Label: VIDEO1, VIDEO2 CN Type: D

NANO-QM57A EPIC SBCPage IV Table of Contents 1 INTRODUCTION...

NANO-QM57A EPIC SBCPage 28 Pin Description Pin Description Pin Description C1 Analog Red -- -- -- -- C2 Analog Green -- -- -- -- C3 Ana

NANO-QM57A EPIC SBC Page 29Speed LED Activity/Link LED STATUS DESCRIPTION STATUS DESCRIPTION Off 10 Mbps connection Off No link Green 100 M

NANO-QM57A EPIC SBCPage 30 4 Installation Chapter 4

NANO-QM57A EPIC SBC Page 314.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the NANO-QM57A may resul

NANO-QM57A EPIC SBCPage 32 4.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read

NANO-QM57A EPIC SBC Page 33o When working with the NANO-QM57A, make sure that it is disconnected from all power supplies and that no electricity is

NANO-QM57A EPIC SBCPage 34 4.4.1 Socket G CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be

NANO-QM57A EPIC SBC Page 35 Figure 4-1: Make sure the CPU socket retention screw is unlocked Step 2: Inspect the CPU socket. Make sure there are no

NANO-QM57A EPIC SBCPage 36 Figure 4-2: Lock the CPU Socket Retention Screw 4.4.2 Socket G Cooling Kit Installation An IEI Socket G CPU cooling ki

NANO-QM57A EPIC SBC Page 37 Figure 4-3: Cooling Kit Support Bracket Step 2: Open the lever at the top of the heat sink. Lift the lever at the top o

NANO-QM57A EPIC SBC Page V3.2.13 USB Connectors... 25 3.3

NANO-QM57A EPIC SBCPage 38 4.4.3 SO-DIMM Installation To install an SO-DIMM, please follow the steps below and refer to Figure 4-4. Figure 4-4: SO-

NANO-QM57A EPIC SBC Page 39Before the NANO-QM57A is installed in the system, the jumpers must be set in accordance with the desired configuration. T

NANO-QM57A EPIC SBCPage 40 Figure 4-6: AT Auto Button Select Jumper Settings 4.5.2 AT/ATX Power Select Jumper Settings Jumper Label: J_ATXCTL1 Jum

NANO-QM57A EPIC SBC Page 414.5.3 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header (1x3) Jumper Settings: See 5Table 4-4 Jumper Loca

NANO-QM57A EPIC SBCPage 42 Figure 4-8: Clear CMOS Jumper 4.5.4 ME RTC Register Jumper Jumper Label: ME_RTC1 Jumper Type: 3-pin header Jumper Setti

NANO-QM57A EPIC SBC Page 434.5.5 ME RTC Flash Security Override Jumper Jumper Label: JP1 Jumper Type: 2-pin header Jumper Settings: See Table 4-6 J

NANO-QM57A EPIC SBCPage 44 power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface. 4.6.2 Mo

NANO-QM57A EPIC SBC Page 45 Figure 4-11: Power Cable to Motherboard Connection Step 3: Connect Power Cable to Power Supply. Connect one of the 4-pi

NANO-QM57A EPIC SBCPage 46 Figure 4-12: Connect Power Cable to Power Supply 4.7.2 Audio Kit Installation The Audio Kit that came with the NANO-QM57

NANO-QM57A EPIC SBC Page 47 Figure 4-13: Audio Kit Cable Connection Step 3: Connect the audio devices. Connect speakers to the line-out audio jack.

NANO-QM57A EPIC SBCPage VI 5.1 INTRODUCTION...

NANO-QM57A EPIC SBCPage 48 Step 2: Insert the cable connector. Insert the connector into the serial port box header. See Figure 4-14. A key on the

NANO-QM57A EPIC SBC Page 49To install these devices, connect the corresponding cable connector from the actual device to the corresponding NANO-QM57

NANO-QM57A EPIC SBCPage 50 Figure 4-15: DVI Connector Step 4: Secure the connector. Secure the DVI-I connector from the digital display device to

NANO-QM57A EPIC SBC Page 51 Figure 4-16: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-

NANO-QM57A EPIC SBCPage 52 Figure 4-17: USB Connector 4.8.4 VGA Monitor Connection The NANO-QM57A is shipped with a DVI-I (male) to VGA adapter (fe

NANO-QM57A EPIC SBC Page 53Step 5: Align the VGA connector. Align the male DB-15 connector on the VGA screen cable with the female DB-15 connector

NANO-QM57A EPIC SBCPage 54 NOTE: If the installation program doesn't start automatically: Click "Start->My Computer->CD Drive->a

NANO-QM57A EPIC SBC Page 55 Figure 4-20: Available Drivers Step 5: Install all of the necessary drivers in this menu. Step 0:

NANO-QM57A EPIC SBCPage 56 5 BIOS Screens Chapter 5

NANO-QM57A EPIC SBC Page 575.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system setti

NANO-QM57A EPIC SBC Page VIIC.1.2 Supported Operating System... 97 C.2 SETUP

NANO-QM57A EPIC SBCPage 58 Key Function F4 key Save all the CMOS changes Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a

NANO-QM57A EPIC SBC Page 595.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview

NANO-QM57A EPIC SBCPage 60 Î System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. Î S

NANO-QM57A EPIC SBC Page 615.3.1 ACPI Configuration The ACPI Configuration menu (BIOS Menu 3) configures the Advanced Configuration and Power Interf

NANO-QM57A EPIC SBCPage 62 5.3.2 CPU Configuration Use the CPU Configuration menu (BIOS Menu 4) to view detailed CPU specifications and configure th

NANO-QM57A EPIC SBC Page 635.3.3 SATA Configuration Use the SATA Configuration menu (BIOS Menu 5) to change and/or set the configuration of the SATA

NANO-QM57A EPIC SBCPage 64 Î Enhanced DEFAULT Configures the Serial-ATA controller to be in enhanced mode. In this mode, IDE channels and SATA chann

NANO-QM57A EPIC SBC Page 65Î All USB Devices [Enabled] Use the All USB Devices option to enable the USB devices. Î Disabled All USB devices are di

NANO-QM57A EPIC SBCPage 66 5.3.5 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations for th

NANO-QM57A EPIC SBC Page 675.3.5.1.1 Serial Port 0 Configuration Î Serial Port [Enabled] Use the Serial Port option to enable or disable the serial

NANO-QM57A EPIC SBCPage VIII List of Figures Figure 1-1: NANO-QM57A...

NANO-QM57A EPIC SBCPage 68 5.3.5.1.2 Serial Port 1 Configuration Î Serial Port [Enabled] Use the Serial Port option to enable or disable the serial

NANO-QM57A EPIC SBC Page 695.3.6 H/W Monitor The H/W Monitor menu (BIOS Menu 9) shows the operating temperature, fan speeds and system voltages. Apt

NANO-QM57A EPIC SBCPage 70 Î Auto RPM Mode DEFAULT The fan adjusts its speed using these settings by RPM: First Boundary Temperature Second Bou

NANO-QM57A EPIC SBC Page 71 NOTE: Smart fan functions are supported only when using a 4-pin fan. When using a 3-pin fan, the functions are not su

NANO-QM57A EPIC SBCPage 72 When the fan is off, it will only start when the temperature exceeds this setting.  Minimum Value: 1°C  Maximum Value

NANO-QM57A EPIC SBC Page 73 Maximum Value: 100% Î Segment 4 Speed Count [060] This value is always full speed and corresponds to the Fourth Bound

NANO-QM57A EPIC SBCPage 74 o +12 V o +1.5V o VSB3V o VBAT 5.3.7 AMT Configuration The AMT Configuration menu (BIOS Menu 10) allows the advanced

NANO-QM57A EPIC SBC Page 75Î Disabled DEFAULT Not perform AMT/ME unconfigure Î Enabled To perform AMT/ME unconfigure 5.3.8 Serial Port Console Redi

NANO-QM57A EPIC SBCPage 76 5.3.8.1 Console Redirection Settings The Console Redirection Settings menu (BIOS Menu 12) allows the console redirection

NANO-QM57A EPIC SBC Page 77Î 9600 The transmission speed is 9600 Î 19200 The transmission speed is 19200 Î 57600 The transmission speed is 57600

NANO-QM57A EPIC SBC Page IXFigure 4-12: Connect Power Cable to Power Supply...46 Figure

NANO-QM57A EPIC SBCPage 78 5.4.1 Northbridge Configuration Use the Northbridge Chipset Configuration menu (BIOS Menu 14) to configure the Northbridg

NANO-QM57A EPIC SBC Page 79Î IGD Memory [32 MB] Use the IGD Memory option to specify the amount of system memory that can be used by the Internal g

NANO-QM57A EPIC SBCPage 80 Î Power On DEFAULT The system turns on Î Last State The system returns to its previous state. If it was on, it turns i

NANO-QM57A EPIC SBC Page 815.4.3 Integrated Graphics Use the Integrated Graphics menu to configure the video device connected to the system. Aptio S

NANO-QM57A EPIC SBCPage 82  EFP  EFP1  CRT + CRT1  CRT + EFP1 5.5 Boot Use the Boot menu (BIOS Menu 17) to configure system boot options. Apti

NANO-QM57A EPIC SBC Page 83Î Off Does not enable the keyboard Number Lock automatically. To use the 10-keys on the keyboard, press the Number Lock

NANO-QM57A EPIC SBCPage 84 5.6 Security Use the Security menu (BIOS Menu 18) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2

NANO-QM57A EPIC SBC Page 855.7 Exit Use the Exit menu (BIOS Menu 19) to load default BIOS values, optimal failsafe values and to save configuration

NANO-QM57A EPIC SBCPage 86 Î Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup pro

NANO-QM57A EPIC SBC Page 87Appendix A A Intel® AMT Configuration