Iei-integration NANO-945GSE v1.01 Manual de usuario Pagina 102
- Pagina / 223
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
NANO-945GSE EPIC Motherboard
Page 82
CF Card Setup Description
Open Slave Default
Closed Master
Table 5-3: CF Card Setup Jumper Settings
The CF Card Setup jumper location is shown in 882HFigure 5-5.
Figure 5-5: CF Card Setup Jumper Location
5.5.3 Clear CMOS Jumper
Jumper Label:
J_CMOS1
Jumper Type:
3-pin header
Jumper Settings:
See
830H883HTable 5-4
Jumper Location:
See
831H884HFigure 5-6
If the NANO-945GSE fails to boot due to improper BIOS settings, the clear CMOS jumper
clears the CMOS data and resets the system BIOS information. To do this, use the jumper
cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1
and 2.
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
Enter the correct CMOS setting
- NANO-945GSE 1
- Revision 2
- Copyright 3
- Manual Conventions 4
- Packing List 6
- Table of Contents 7
- List of Figures 13
- List of Tables 17
- List of BIOS Menus 19
- Page xx 20
- 1 Introduction 21
- 1.1 Overview 22
- 1.2 NANO-945GSE Overview 22
- Serial Infrared (SIR) 27
- 2 Detailed Specifications 28
- 2.1 Dimensions 29
- 2.2 Data Flow 30
- 794HFigure 2-4 below 31
- L2 Dynamic Cache Sizing 33
- 796HFigure 2-6 below 34
- CPIS 1.5 compliant 36
- 797HFigure 2-8 37
- Back right 40
- Center 40
- Subwoofer 40
- 799HFigure 2-10 42
- 800HFigure 2-11 below 42
- Page 24 44
- 802HFigure 45
- 2.6 LPC Bus Components 47
- Page 28 48
- Keyboard Controller 49
- Watchdog Timer 49
- Page 32 52
- 2.7.3 Power Consumption 52
- 3 Unpacking 53
- 3.1 Anti-static Precautions 54
- 3.2 Unpacking 54
- 3.3 Unpacking Checklist 55
- Page 36 56
- 3.3.2 Optional Items 56
- 4 Connectors 58
- 4.1.1 NANO-945GSE Layout 59
- Page 40 60
- Page 42 62
- 4.3.1 5V Power Connector 62
- 815HFigure 4-4 63
- 816HTable 4-4 63
- PIN NO. DESCRIPTION 65
- 2 PS-ON 65
- 3 +5V Standby 65
- Page 46 66
- 1 LCD Backlight Control 67
- 2 GROUND 67
- 4 GROUND 67
- 5 BACKLIGHT Enable 67
- Page 48 68
- Page 50 70
- Page 52 72
- 787H833HFigure 4-13 74
- 788H834HTable 4-13 74
- 5 KB CLK 76
- 6 GROUND 76
- 1 GND1 2 GND2 76
- 3 A_Y0 4 A_Y0# 76
- 839HFigure 4-16 78
- 840HTable 4-17 78
- Page 60 80
- 4.3.16 PCI-104 Slot 80
- Page 62 82
- 793H845HFigure 4-19 83
- 794H846HTable 4-20 83
- 799H851HFigure 4-22 86
- 800H852HTable 4-23 86
- 801H853HFigure 4-23 86
- 802H854HTable 4-24 86
- 856HFigure 4-24 (labeled 1) 88
- 811H862HFigure 4-24 (see 2) 90
- Figure 4-28: VGA Connector 92
- 5 Installation 93
- 5.1 Anti-static Precautions 94
- Read the user manual: 95
- Page 76 96
- 5.2.2 Installation Checklist 96
- 5.3 Unpacking 97
- 871HFigure 5-1) 98
- 872HFigure 5-1) 98
- 873HFigure 5-2. Step 0: 98
- 875HTable 5-2 100
- 876HFigure 5-4 100
- 877HTable 5-2 100
- CF Card Setup Description 102
- Open Slave Default 102
- Closed Master 102
- 887HTable 5-5 103
- 888HFigure 5-7 103
- 832H885HTable 5-4 103
- 833H886HFigure 5-6 below 103
- NANO-945GSE EPIC Motherboard 105
- Short 1-2 +3.3V LVDS 106
- Short 1-2 +5V 107
- Short 2-3 +3.3V 107
- 5.6 Chassis Installation 108
- Dual port USB cable 109
- Parallel port cable 109
- RS-232/422/485 cable 109
- ATX power cable 109
- 904HFigure 5-11 110
- [email protected] 112
- [email protected] 114
- 906HFigure 5-14 114
- 852H908HFigure 5-16 116
- 912HFigure 5-19 120
- 913HFigure 5-20 120
- 916HFigure 5-22 122
- 858H917HFigure 5-23 124
- Step 0: 126
- 863H921HFigure 5-27 127
- 6 BIOS Screens 129
- 6.1 Introduction 130
- Page 112 132
- 6.3 Advanced 133
- Page 114 134
- 6.3.1 CPU Configuration 134
- Page 115 135
- 6.3.2 IDE Configuration 135
- Page 116 136
- Page 117 137
- Page 118 138
- DEFAULT 143
- Page 124 144
- Page 128 148
- CPU Fan Start PWM 149
- Slope PWM 1 149
- CPU Fan PWM control 149
- Minimum Value: 0°C 149
- Maximum Value: 127°C 149
- Page 130 150
- Page 131 151
- 6.3.5 Power Configuration 151
- Page 132 152
- 6.3.5.1 ACPI configuration 152
- Page 134 154
- Page 136 156
- 6.3.6 Remote Configuration 156
- Page 137 157
- Page 138 158
- Page 139 159
- Page 140 160
- 6.3.7 USB Configuration 160
- 6.4 PCI/PnP 162
- IRQ3 163
- IRQ4 163
- IRQ5 163
- IRQ7 163
- 6.5 Boot 165
- 6.6 Security 169
- 6.7 Chipset 170
- 64MB 172
- 128MB DEFAULT 172
- Maximum DVMT 172
- 6.8 Exit 175
- Page 156 176
- 7 Software Drivers 177
- Page 158 178
- Page 159 179
- Page 160 180
- Page 161 181
- Page 162 182
- Page 163 183
- Page 164 184
- 7.4 VGA Driver Installation 185
- Page 166 186
- Page 167 187
- Page 168 188
- Page 169 189
- 7.5 LAN Driver Installation 190
- Page 171 191
- Page 172 192
- Page 173 193
- 7.6.1 HD Audio Installation 193
- Page 174 194
- Page 175 195
- Page 176 196
- Page 177 197
- Page 178 198
- Page 179 199
- A BIOS Menu Options 200
- B Terminology 204
- Page 185 205
- Page 186 206
- Page 187 207
- Page 188 208
- C DIO Interface 209
- C.2 DIO Connector Pinouts 210
- D Watchdog Timer 212
- E Address Mapping 215
- E.1 I/O Address Map 216
- Page 197 217
- E.2 IRQ Address Map 218
- E.3 Memory Address Map 219
- F Hazardous Materials 220
- Disclosure 220
- Page 201 221
Relacionado con productos y manuales para Hardware Iei-integration NANO-945GSE v1.01
Hardware Iei-integration NANO-945GSE2 Manual de usuario
(172 paginas)
(172 paginas)
Hardware Iei-integration NANO-QM57A Manual de usuario
(143 paginas)
(143 paginas)
Hardware Iei-integration NANO-HM650 Manual de usuario
(175 paginas)
(175 paginas)
Hardware Iei-integration NANO-QM770 Manual de usuario
(190 paginas)
(190 paginas)
Hardware Iei-integration NANO-HM651 Manual de usuario
(165 paginas)
(165 paginas)
Hardware Iei-integration NANO-QM871 Manual de usuario
(203 paginas)
(203 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales