Iei-integration NANO-9453 v1.12 Manual de usuario Pagina 135
- Pagina / 242
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
NANO-9453 EPIC Motherboard
Page 117
BIOS Menu 5: IDE Master and IDE Slave Configuration
Auto-Detected Drive Parameters
The “grayed-out” items in the left frame are IDE disk drive parameters automatically
detected from the firmware of the selected IDE disk drive. The drive parameters are listed
as follows:
Device: Lists the device type (e.g. hard disk, CD-ROM etc.)
Type: Indicates the type of devices a user can manually select
LBA Mode: Indicates whether the LBA (Logical Block Addressing) is a
method of addressing data on a disk drive is supported or not.
Block Mode: Block mode boosts IDE drive performance by increasing the
amount of data transferred. Only 512 bytes of data can be transferred per
interrupt if block mode is not used. Block mode allows transfers of up to 64 KB
per interrupt.
PIO Mode: Indicates the PIO mode of the installed device.
Async DMA: Indicates the highest Asynchronous DMA Mode that is
supported.
- NANO-9453 EPIC Motherboard 1
- Revision 2
- Copyright 3
- Manual Conventions 4
- Packing List 6
- Table of Contents 7
- List of Figures 13
- List of Tables 16
- BIOS Menus 18
- 1 Introduction 19
- 1.1 Introduction 20
- 1.2 NANO-9453 Overview 21
- 2 Detailed Specifications 25
- 2.1 Overview 26
- 2.2 Dimensions 26
- 2.3 Data Flow 28
- 2.4 Compatible Processors 29
- Page 12 30
- 2.5 Intel 32
- 945GME Northbridge Chipset 32
- LVDS 33
- SDVO 33
- 32-bit downstream address 36
- 2.6 Intel 37
- ICH7-M Southbridge Chipset 37
- Supports two SATA drives 42
- 2.7 PCIe Bus Components 43
- JTAG support 44
- 2.8 LPC Bus Components 45
- AMI Flash BIOS 46
- Standard mode 48
- Enhanced mode 48
- High-speed mode 48
- Page 32 50
- 3 Unpacking 52
- 3.1 Anti-static Precautions 53
- 3.2 Unpacking 53
- 3.3 Unpacking Checklist 54
- 4 Connector Pinouts 58
- Page 44 62
- PIN NO. DESCRIPTION 63
- 2 PS_ON# 65
- 3 +5V Standby 65
- Page 48 66
- 4.2.5 Compact Flash Socket 66
- Page 50 68
- 1 GND 2 VCC 69
- 3 Output 3 4 Output 2 69
- 5 Output 1 6 Output 0 69
- 7 Input 3 8 Input 2 69
- 9 Input 1 10 Input 0 69
- Page 52 70
- Page 54 72
- 4.2.9 IDE Connector(44-pin) 72
- 3 IR-RX 74
- 5 IR-TX 74
- 23 N/C 24 N/C 76
- 25 GROUND 26 GROUND 76
- 27 VCC_LVDS 28 VCC_LVDS 76
- 29 VCC_LVDS 30 VCC_LVDS 76
- Page 60 78
- Page 62 80
- Page 64 82
- 4.2.15 SATA Drive Connectors 82
- 1 TXD485# 84
- 2 TXD485+ 84
- 3 RXD485+ 84
- 4 RXD485# 84
- PIN DESCRIPTION PIN 89
- DESCRIPTION 89
- 1 VCC 5 VCC 90
- 2 DATA- 6 DATA 90
- 3 DATA+ 7 DATA+ 90
- 4 GROUND 8 GROUND 90
- Figure 4-24: VGA Connector 91
- 5 Installation 92
- 5.1 Anti-static Precautions 93
- Read the user manual: 94
- 5.2.2 Installation Checklist 95
- Page 80 98
- Page 82 100
- Page 84 102
- 5.3.4 CF Card Installation 102
- NOTE: 104
- CF Card Setup Description 105
- Open Slave Default 105
- Short Master 105
- 5.4.2 Clear CMOS Jumper 106
- Page 88 106
- Short 1-2 RS-232 Default 107
- Short 3-4 RS-422 107
- Short 5-6 RS-485 107
- Short 2-3 +5V LVDS 108
- Short 1-2 VCC 109
- Short 2-3 VCC3 109
- 5.5 Chassis Installation 110
- USB cable 111
- RS-232/422/485 cable 111
- LPT cable 111
- ATX power cable 111
- Page 96 114
- Page 102 120
- Figure 5-24: USB Connector 125
- 6 AMI BIOS 126
- 6.1 Introduction 127
- 6.2 Main 129
- 6.3 Advanced 130
- Page 114 132
- Configuration 133
- Primary IDE Master 134
- Primary IDE Slave 134
- Secondary IDE Master 134
- Secondary IDE Slave 134
- Page 117 135
- DEFAULT 141
- CPU Temp. Limit of OFF 145
- Page 128 146
- Page 129 147
- Page 130 148
- Page 142 160
- 6.3.9 USB Configuration 160
- 6.4 PCI/PnP 164
- Clear NVRAM [No] 165
- 6.5 Boot 171
- CD/DVD 174
- Page 157 175
- 6.6 Security 176
- 6.7 Chipset 177
- Page 162 180
- IGD DEFAULT 182
- PCI/IGD 182
- Page 166 184
- Page 167 185
- Page 168 186
- 6.8 Exit 187
- Page 170 188
- 7 Driver Installation 189
- 7.2 Driver CD Auto-run 190
- ES to continue the setup 192
- Page 177 195
- Page 178 196
- Page 179 197
- Page 180 198
- Page 181 199
- Page 182 200
- EL during POST 201
- EXT. See Figure 7-24 203
- INISH” button. Step 0: 204
- EXT” button. The install 206
- ” button 207
- Page 191 209
- A BIOS Options 210
- B Terminology 215
- Page 198 216
- Page 199 217
- Page 200 218
- Page 201 219
- C DIO Interface 220
- C.2 DIO Connector Pinouts 221
- D Watchdog Timer 223
- E Address Mapping 226
- E.1 Address Map 227
- E.3 IRQ Mapping Table 228
- E.4 DMA Channel Assignments 229
- F Compatibility 230
- F.2 Compatible Processors 231
- G Hazardous Materials 233
- Disclosure 233
- Page 216 234
- H Index 237
Relacionado con productos y manuales para Hardware Iei-integration NANO-9453 v1.12
Hardware Iei-integration NANO-HM650 Manual de usuario
(175 paginas)
(175 paginas)
Hardware Iei-integration NANO-QM770 Manual de usuario
(190 paginas)
(190 paginas)
Hardware Iei-integration NANO-HM651 Manual de usuario
(165 paginas)
(165 paginas)
Hardware Iei-integration NANO-QM871 Manual de usuario
(203 paginas)
(203 paginas)
Hardware Iei-integration PM-945GSE Manual de usuario
(122 paginas)
(122 paginas)
Hardware Iei-integration WAFER-LX v1.0 Manual de usuario
(144 paginas)
(144 paginas)
Hardware Iei-integration PM-LX2-800 Manual de usuario
(123 paginas)
(123 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales